SPE Library


The SPE Library contains thousands of papers, presentations, journal briefs and recorded webinars from the best minds in the Plastics Industry. Spanning almost two decades, this collection of published research and development work in polymer science and plastics technology is a wealth of knowledge and information for anyone involved in plastics.

The SPE Library is just one of the great benefits of being an SPE member! Are you taking advantage of all of your SPE Benefits?

Not an SPE member? Join today!

Use % to separate multiple keywords. 


Search SPE Library
    
    




Sort By:  Date Added   Publication Date   Title   Author

Conference Proceedings

Effect of Strain Rate on PVC Impact Performance
Amiel Sabbagh, May 2002

The impact behavior of poly(vinyl chloride) (PVC) siding formulations containing chlorinated polyethylene (CPE) and acrylic core-shell impact modifiers was evaluated using an instrumented impact tester. The samples were tested at room temperature over a range of testing speeds. Differences in strain rate sensitivity were observed for the various formulations. The differences appear to be a result of both the impact modifiers and the overall formulation.

Effect of Structural Relaxation on Dynamic Mechanical Properties of Poly(Methyl Methacrylate)
B.R. Davis, N. Mekhilef, May 2002

Mechanical spectra of atactic poly(methyl methacrylate) were measured via dynamic mechanical analysis. Measurements were taken on specimens annealed in the temperature range of 23 to 100°C for varying lengths of time. It was found that the effects of thermal treatment are more varied than previously reported, with significant differences found in the breadth and location of the ? and ? relaxation peaks.

Effect of the Mesh Number Elements in the Simulation Results of Normalized Test Specimens Injection Molded
S. Villarroel, R.A. Morales, A. Sánchez, May 2002

The study was made by modifying the simulation mesh model characteristics to mold normalized test specimens. The simulation results were obtained through a filling/cooling simulation program for the injection molding process. The simulated filling time, optimum cycle time and injection pressure, seemed to be influence by the number of elements model. A best agreement between experimental and simulation results were obtained by increasing the number of elements of the mesh model.

Effect of Wall Slip of Polymer Melts on their Relaxation Modulus Behavior
Dilhan M. Kalyon, Halil Gevgilili, May 2002

The determination of the relaxation modulus using the step imposition of a strain is an important step in the fitting of the parameters of viscoelastic constitutive equation. In the nonlinear region the true shear strain imposed on a polyethylene melt is found to deviate considerably from the targeted strain due to the presence of wall slip which is documented here. The presence of the wall slip reduces the range of strains for which the strain-dependent relaxation modulus can be determined for the linear polyethylene melt investigated.

The Effects of Dynamic Vulcanization on the Morphology and Mechanical Property of Rubber/Plastic Blends
Oansuk Chung, Aubert Y. Coran, May 2002

The effects of dynamic vulcanization on the morphology and mechanical properties of rubber/plastic blends are investigated. This study includes the discussion of why the mechanical properties differ before and after dynamic vulcanization. Enhanced interfacial adhesion by dynamic vulcanization was found to be a major contributor of superior tensile strength of TPV. Rubber elasticity of TPV is a result of the combined effects of crosslinked rubber, morphology, and amorphous PP phase plasticization.

The Effects of Extreme Stress during the Injection Process on Polypropylene
Stephanie L. Bullard, Matthew M. Jackson, May 2002

The strength and viscosity of polypropylene is influenced by extreme stress during the injection process. By varying backpressure of the material in extreme conditions the strength of the part will decrease. Reduced strength of the part will be proven through tensile and impact testing. Numerous material generations of polypropylene will be compared to virgin polypropylene to prove the decrease in strength.

Effects of Lubricants on Processing of Polymer-Wood Composites
Joe B. Williams, Kenn S. Geick, May 2002

A number of lubricants have been evaluated in polymer-wood composites. These lubricants have been evaluated in both HDPE-oak and HDPE-pine composites. Properties measured included extruder torque levels, outputs, extruder shear heating, and visual assessment of extruded part appearance.

The Effects of Machine Nozzle and Sprue Design in Mold Filling Imbalances
Ryan T. Paszkowski, Kathryn E. Garnavish, May 2002

The imbalance between the cavities in a geometrically balanced, multi-cavity mold used for injection molding has previously been explained in theory as shear induced imbalances". (1) The cause of these imbalances can be from uneven shear effects on the melt as it travels to each cavity through the runner. This paper presents a study which finds that the machine nozzle and sprue can have a significant contribution to shear induced mold filling imbalance. The effect of geometry material and process are evaluated."

Effects of Nanocomposites on the Oxygen Barrier Properties of Polyethylene
Shawn D. McConaughy, May 2002

The Permeability of polyethylene limits it's use in applications where oxygen barrier properties are required. Polyethylene, an extremely non-polar molecule, exhibits low permeation levels with polar substances such as water. Conversely, non-polar gasses such as oxygen exhibit high levels of permeation. A silicate nanocomposite was added to reduce the permeation of non-polar gasses while maintaining the low permeation of polar substances. The polyethylene nanocomposite provided better oxygen permeation properties than traditional grades of polyethylene.

Enhanced Impact Modifier for Rigid PVC Formulations
Lawrence J. Effler, Mark T. Berard, May 2002

A new chlorinated polyethylene has been developed for the impact modification of rigid PVC. In addition to imparting excellent impact, the modifier promotes faster PVC fusion, and enhances the formulation's melt strength. Faster fusion allows for economic savings by reducing fusion promoting ingredients and via higher output. The enhanced melt strength results in better part quality, especially for complex profiles.

Enhanced Weatherability of Exterior PVC Building Products - Part II
Charles Crabb, Peggy Schipper, May 2002

Low levels of acrylics are widely used as impact modifiers and processing aids for rigid PVC. At higher levels, acrylics can also significantly improve the long- term weatherability of PVC. Here we report on the ongoing results of a long-term outdoor weathering study of PVC/acrylic blends. Acrylic level, stabilizer type, and weathering location all affected the property retention of the weathered specimens. With proper formulation, the acrylic blends resulted in a significant improvement in the weatherability of the samples versus the PVC controls.

Epoxy Resins from Vegetable Oils
Zoran S. Petrovi?, Wei Zhang, Randy Miller, Ivan Javni, May 2002

Epoxidized soybean oil was cured with citric acid, phthalic anhydride and Lewis acids. Lewis acid initiators and citric acid gave rubbery materials of relatively low strength and low glass transition. Aromatic anhydrides give glassy polymers when equivalent ratio of anhydride to epoxy group is used. Mechanical strength of rubbers is relatively low but that of the glassy materials is typical for plastic materials.

Evaluation of Design and Processing Parameters for Extrusion Blow Mold Pinch-Off Design
Cody D. Greene, Ian S. Laskowitz, John E. McConnell, May 2002

Pinch-off weld line strength is crucial in ext rusion blow molding. This experiment is intended to determine and quantify the processing parameters and design parameters that will produce the strongest weld line strength. Using a 3 level Design of Experiment (DOE) for making the test specimens, the specimens were tested for tensile strength. This data was then used as a guide for producing quality pinch-off weld lines with less guesswork.

Evaluation of Runner Design for Powdered Metal Injection Molding
Michael Bailey, Andrew Schenck, May 2002

It has been observed that a filling imbalance occurs with powdered metal injection molding in multi cavity molds using geometrically balanced runners. This imbalance is typically opposite to the shear induced imbalance developed n these runners with conventional plastic materials The causes and effects of this reversed condition is studied and alternative runner designs evaluated to reduce the imbalance. The alternative designs include the use of the MeltFlipper technology that has proven to solve the imbalance with conventional plastic materials.

Examination of Finite Element Analysis and Experimental Results of Quasi-Statically Loaded Acetal Copolymer Gears
Paul Wyluda, Dan Wolf, May 2002

An elastic-plastic finite element analysis of the quasi-static loading of two acetal copolymer gears in contact is preformed. Load verses rotation of the gear set is compared to actual experimental results. The gear geometry is modeled by plane strain elements with variable thickness between the rim and web. Gear tooth failure is modeled by both deactivating and separating elements when the tensile strength is exceeded. Failure in the tooth root is best modeled by a nonlinear approach using separating elements.

An Experimental Investigation of Screw Configuration on Temperature Rise in Single Screw-Pump Extruders
Gregory A. Campbell, Hongying Cheng, Chicheng Wang, Matthew Bullwinkel, Mary Ann te-Riele, May 2002

The focus of this investigation was to experimentally determine the effect of barrel rotation and screw rotation viscous dissipation inside the screw pump-extruder. The experimental results can be summarized by noting that barrel rotation generated higher temperature rise than screw rotation. Results are presented for seven screw configurations.

An Experimental Study of the Flows in an Energy Transfer Screw
Susan A. Somers, Mark A. Spalding, Joseph Dooley, Kun Sup Hyun, May 2002

A comparison is made between the melting, pumping, and mixing characteristics of a single-screw extruder with an Energy Transfer mixing section and a conventional screw without a mixing section. Results are given for extrusion trials, extrudate sampling, and extrusion solidification experiments performed at different screw speeds and color concentration letdown ratios.

Film Blowing of a Narrow Molecular Weight Polyethylene
Michael A. McLeod, May 2002

Four homopolymer high density polyethylene (HDPE) resins were evaluated for their blown film properties. Film was blown in both conventional linear low density polyethylene (LLDPE) configuration and high molecular weight - high density polyethylene (HMW-HDPE) configuration. Water vapor transmission rates were reduced by nearly 50% in the HMW-HDPE configuration for the narrow molecular weight resins. Haze increased and gloss decreased for the same polymers. The broad molecular weight polymer showed only small changes in these properties.

Film Properties for Good Performance on Vertical Form/Fill/Seal Packaging Machines
Terry A. Clark, John R. Wagner, Jr., May 2002

Technological improvements of flexible form, fill and seal packaging machines are yielding exceptional line speeds, productivity rates and bag features. This paper discusses the evolution of vertical packaging machine development and how it has impacted plastic film properties (e.g. COF, sealing temperature range, hot tack) required for optimal performance.

Fin Assembly in Energy Management
Kal Renganathan Sharma, May 2002

Heat sinking in electronic components in VLSI can be any method by fin assemblies in different configuration. The periodic heating is studied using hyperbolic heat wave propagative equation complex variables. The flux reversal is studied.







SPE-Inspiring Plastics Professionals

© 2024 SPE-Inspiring Plastics Professionals.
All rights reserved.

84 countries and 60k+ stakeholders strong, SPE unites plastics professionals worldwide – helping them succeed and strengthening their skills through networking, events, training, and knowledge sharing.

No matter where you work in the plastics industry value chain-whether you're a scientist, engineer, technical personnel or a senior executive-nor what your background is, education, gender, culture or age-we are here to serve you.

Our members needs are our passion. We work hard so that we can ensure that everyone has the tools necessary to meet her or his personal & professional goals.

Contact Us | Sitemap | Data Privacy & Terms of Use

Links

Locations

SPE US Office
83 Wooster Heights Road, Suite 125
Danbury, CT 06810
P +1 203.740.5400

SPE Australia/New Zealand
More Information

SPE Europe
Serskampsteenweg 135A
9230 Wetteren, Belgium
P +32 498 85 07 32

SPE India
More Information

SPE Middle East
More Information

3Dnatives Europe
157 Boulevard Macdonald
75017, Paris, France
More Information

Powered By SPE

SPE-Inspiring Plastics Professionals

SPE-Inspiring Plastics Professionals

SPE ImplementAM

SPE-Inspiring Plastics Professionals

SPE-Inspiring Plastics Professionals

SPE-Inspiring Plastics Professionals




spe2018logov4.png
  Welcome Page

How to reference articles from the SPE Library:

Any article that is cited in another manuscript or other work is required to use the correct reference style. Below is an example of the reference style for SPE articles:

Brown, H. L. and Jones, D. H. 2016, May.
"Insert title of paper here in quotes,"
ANTEC 2016 - Indianapolis, Indiana, USA May 23-25, 2016. [On-line].
Society of Plastics Engineers
Available: www.4spe.org.

Note: if there are more than three authors you may use the first author's name and et al. EG Brown, H. L. et al.

If you need help with citations, visit www.citationmachine.net