SPE Library


The SPE Library contains thousands of papers, presentations, journal briefs and recorded webinars from the best minds in the Plastics Industry. Spanning almost two decades, this collection of published research and development work in polymer science and plastics technology is a wealth of knowledge and information for anyone involved in plastics.

The SPE Library is just one of the great benefits of being an SPE member! Are you taking advantage of all of your SPE Benefits?

Not an SPE member? Join today!

Use % to separate multiple keywords. 


Search SPE Library
    
    




Sort By:  Date Added   Publication Date   Title   Author

Conference Proceedings

Melt Extruded Open-Cell Microcellular Foams for Membrane Separation: Processing and Cell Morphology Relationship
Quan Huang, Bernd Seibig, Dieter Paul, May 1999

This paper presents an experimental study on the manufacture of microcellular polycarbonate in a designed twin-screw extrusion system using CO2 as blowing agent. Open-cell microcellular polycarbonate foams in the form of hollow fiber were produced with a cell density on the order of 109-1010 cell/cm3 and an average cell size in the range of 5-10 µm. The effects of the processing conditions on the cell morphology and the cell-opening technique are described.

Superior Customer Service: A Competitive Advantage
Margaret H. Baumann, May 1999

In this period of increased competition and expected quality superior customer service remains an area for differentiation and competitive advantage. Technology has offered customer service enabling tools but does not ensure superior customer service. This paper will discuss what is superior customer service" today and in the future and how your company can gain a competitive advantage through its customer service."

Importance of Injection Molding Parameters for Mechanical Performance of Cold Flow Weld Lines
R.P. Koster, May 1999

Tensile and tensile-impact test results are reported on specimens with a cold weld line and identical specimens without weld line. Pairs of specimens without and with weld line have been injection molded simultaneously. Test results indicate that the effect of flow-induced stresses on weld line strength should be taken into account, in addition to the well-known influence of material temperatures during molding.

A Unified Approach for Thermoforming Numerical Simulation
M. Rachik, J.M. Roelandt, May 1999

In this paper, we present a unified approach for numerical simulation of thermoforming process. In contrast with iterative methods and dynamic explicit scheme, we propose a high order explicit algorithm based on the classical 4th order Runge-Kutta scheme. The proposed procedure is used to solve the global equilibrium equations and to integrate the sheet viscoelastic constitutive model. The error and time step size control is performed at each level which increase the procedure robustness and efficiency.

Feasibility of the Use of Polystyrene/Polypropylene Blends
R. Sciamanna, C. Albano, G. Arribas, May 1999

The purpose of this investigation is to study the feasibility of PS/PP blends. The analysis of the results shows that compatibilization of the blend with one kind of SBS copolymer improves some mechanical properties of the blend. However, the amount of copolymer to be added depends on the intended specific uses. The cost/profit relation must always be observed.

Processing Trends of Metallocene Linear Low Density Polyethylenes and Their Influence on Single Screw Design
K.R. Slusarz, C.A. Ronaghan, J.P. Christiano, May 1999

New families of polyolefin resins using single site catalysis technology, are being produced to enhance resin properties. The changes to the molecular architecture of these resins effect the rheological, thermal, frictional, and elastic properties; all of which play a significant role in screw design. This paper will investigate several polyolefin plastomers and compare them to a conventional linear low density polyethylene (LLDPE) to determine their impact on screw design.

Computing an Injection Fill Speed from a Relative Viscosity Curve
J.R. Wareham, J.D. Ratzlaff, May 1999

On-machine rheology is a methodology of determining the flow characteristics of a material at a given temperature with a specific mold and machine. [5] This methodology can be used to help determine the best injection fill speed to be used for a given material, machine and mold combination. This study presents a mathematical method to obtain an injection fill speed starting point when setting up a new mold, machine and material combination.

In Situ Polymer-Polymer Composites
I. Pesneau, A. Aït Kadi, M. Bousmina, P. Cassagnau, A. Michel, May 1999

In situ polymer-polymer composites of polypropylene / polyamide (PP/PA) have been obtained by a two step process. In the first step the components were extruded and the blend has been stretched at the exit of the die. In the second step, the blend was molded either by compression or by injection to obtain real organic composite materials with enhanced mechanical and thermal properties.

Polymer Melt Formation and Densification in Rotational Molding
M. Kontopoulou, E. Takács, J. Vlachopoulos, May 1999

Polymer melt densification, involving particle coalescence followed by the formation and dissolution of bubbles, has been studied in order to evaluate how it is affected by powder properties, chemical structure, thermal properties and rheology. A variety of rotomolding grade resins have been tested, in an effort to understand the mechanisms involved in the melt formation and its subsequent densification.

Effect of Formulation and Processing Conditions on the Viscosity of Masterbatches
Bob Zeller, May 1999

Adding colorants and additives in masterbatches may affect the rheological properties of the resins into which they are mixed, but the extent of this effect has not been fully investigated. This paper reports on a design of experiments (DOE) study of the effect of 3 common colorants, 2 lubricants, a filler, an antioxidant, and 2 processing parameters (melt temperature and screw speed), on the viscosity of a linear low-density polyethylene (LLDPE) masterbatch. The series of experiments determined that only the lubricant and filler had a significant impact on resin rheology.

Press Forming of Filled and Short Fiber Reinforced Nylon-6
Z. Xia, P.K. Mallick, May 1999

An experimental study was undertaken to examine the feasibility of press forming mineral filled and short glass fiber reinforced nylon-6. Press forming was conducted in a matched metal die much like the stamping operation used for sheet metals. The process parameters studied were the sheet preheating temperature, die temperature, forming pressure and sheet clamping. It was shown that with proper adjustment of some of these parameters, both mineral filled and short glass fiber reinforced nylon-6 could be successfully press formed.

Foaming of Polypropylene in Extrusion Processes
Erik Andreassen, Kjetil L. Børve, Kari Rommetveit, Keith Redford, May 1999

Various polypropylene grades were foamed using a small general-purpose twin-screw extruder. Cell diameters of ~70 µm and foam densities of ~14 kg/m3 were achieved with a conventional linear PP, using iso-butane as foaming agent. Linear and branched PP grades were subjected to dynamic rheometry and instrumented haul-off measurements, and the results are discussed in terms of melt strength, viscosity and elasticity. Promising results were obtained for branched materials produced by reactive extrusion.

Simulation of Draw Resonance in Film Casting Using a Material Description of Motion
Spencer Smith, Dieter Stolle, May 1999

This paper summarizes a strategy for the numerical simulation of film casting. The strategy incorporates time-stepping, an updated Lagrangian description of motion and viscoelasticity. The results for an approximately viscous solution agree very well with the theoretical solutions. For a Maxwell fluid it is noted that, as the relaxation time increases, the thickness gradient at the die increases and the velocity decreases. Also, for the case considered, a moderate relaxation time seems to destabilize the polymer.

Designing with Glass Fiber Reinforced Vinyl Composites II - Long Term Creep Considerations
Martin E. Woods, Rabeh Elleithy, May 1999

Six years ago we initiated a long term study on the effect of time and temperature on the data sheet modulus values for glass fiber reinforced vinyl composites. Results after the first year showed that the measured creep modulii were higher than those predicted by time-temperature superposition of dynamic mechanical data. This paper presents five years of additional creep data and examines the effect of sample aging on the creep predictions.

The Use of Conducting Polymer Composites in Thermoplastics for Tuning Surface Resistivity
Sam J. Dahman, Jamshid Avlyanov, May 1999

It is often difficult to provide consistent surface resistivity in the effective static dissipative range (about 105 to 1010 ohms/square). Thermoplastics incorporating traditional conductive additives generally exhibit discontinuous electrical behavior in this range. Conducting polymer composites have been created through in-situ deposition of conducting polymers onto carbon black substrates. By utilizing the inherent flexibility of these conducting polymer composites, compounds have been developed with controlled surface resistivity.

Learning from History: A Key Part of the Development Process of Insite™ Technology
Kurt W. Swogger, May 1999

One of the very first principles used to develop INSITE™ Technology, a major revolution in the polymer industry, was that of learning from history. Analyzing and avoiding repetition of mistakes to do product development worked very much to Dow's advantage as the major piece of technology advanced. Too often not enough time is allotted for contemplation of how to do better based on our collective experiences and wisdom. Particularly in developing new products, experience really makes a huge impact on the speed and success rate.

Nylon 6 in Thin-Wall Housings
James F. Stevenson, Alan Dubin, May 1999

To meet the challenging processing and performance demands for thin-wall housings, plastic materials must satisfy basic requirements for flow, impact resistance, and modulus. In this paper, select mechanical and processing properties of nylon 6 materials are examined for thin-wall-molding applications and compared with those for amorphous blends.

Quality Improvement of Foamed Seals for the Automotive Industry
Annette Krusche, Edmund Haberstroh, May 1999

Automotive body seals are becoming increasingly complex. As there is still little knowledge about the manufacturing process, extensive investigations are done to analyze the influence of the rheological behavior of the materials, the parameters of the extrusion process and the foaming/vulcanization on the quality properties of the foamed seals. The evaluation allows a better process understanding which in combination with improved test methods leads to an increased product quality and reduced manufacturing costs.

Pearl Lustre Pigment Modification - Improving Handling Characteristics
Robin Hilder, Scott Aumann, Emil Aust, May 1999

Synthetic pearl lustre like other high aspect ratio pigments exhibit poor solid flow behaviour. In the extruder based manufacture of thermoplastic masterbatches this limits output, by restricting the conveying capacity of the feed zone. Proprietary wax encapsulation technology now allows four fold or greater improvements in the extruder output without changing the particle shape or size distribution of the pigment prior to the compounding process. The encapsulation process also leads to low dust characteristics.

Chemical Assessment of Automotive Clearcoat Weathering
R.O. Carter III, John L. Gerlock, Cindy A. Smith, May 1999

The top, clearcoat layer of an automotive paint job protects the under layers while maintaining a beautiful appearance for the life of a car. To determine clearcoat durability, effects of the weathering protocol, of the physical and chemical transformations and effects on the appearance must be considered. To this end, we will describe photoacoustic infrared (PAS-IR), and ultraviolet (UV) technologies and UV microspectroscopy to assay the changes in chemical composition produced in clearcoat paint systems by weathering.







SPE-Inspiring Plastics Professionals

© 2024 SPE-Inspiring Plastics Professionals.
All rights reserved.

84 countries and 60k+ stakeholders strong, SPE unites plastics professionals worldwide – helping them succeed and strengthening their skills through networking, events, training, and knowledge sharing.

No matter where you work in the plastics industry value chain-whether you're a scientist, engineer, technical personnel or a senior executive-nor what your background is, education, gender, culture or age-we are here to serve you.

Our members needs are our passion. We work hard so that we can ensure that everyone has the tools necessary to meet her or his personal & professional goals.

Contact Us | Sitemap | Data Privacy & Terms of Use

Links

Locations

SPE US Office
83 Wooster Heights Road, Suite 125
Danbury, CT 06810
P +1 203.740.5400

SPE Australia/New Zealand
More Information

SPE Europe
Serskampsteenweg 135A
9230 Wetteren, Belgium
P +32 498 85 07 32

SPE India
More Information

SPE Middle East
More Information

3Dnatives Europe
157 Boulevard Macdonald
75017, Paris, France
More Information

Powered By SPE

SPE-Inspiring Plastics Professionals

SPE-Inspiring Plastics Professionals

SPE ImplementAM

SPE-Inspiring Plastics Professionals

SPE-Inspiring Plastics Professionals

SPE-Inspiring Plastics Professionals




spe2018logov4.png
  Welcome Page

How to reference articles from the SPE Library:

Any article that is cited in another manuscript or other work is required to use the correct reference style. Below is an example of the reference style for SPE articles:

Brown, H. L. and Jones, D. H. 2016, May.
"Insert title of paper here in quotes,"
ANTEC 2016 - Indianapolis, Indiana, USA May 23-25, 2016. [On-line].
Society of Plastics Engineers
Available: www.4spe.org.

Note: if there are more than three authors you may use the first author's name and et al. EG Brown, H. L. et al.

If you need help with citations, visit www.citationmachine.net