SPE Library
The SPE Library contains thousands of papers, presentations, journal briefs and recorded webinars from the best minds in the Plastics Industry. Spanning almost two decades, this collection of published research and development work in polymer science and plastics technology is a wealth of knowledge and information for anyone involved in plastics.
The SPE Library is just one of the great benefits of being an SPE member! Are you taking advantage of all of your SPE Benefits?
Conference Proceedings
Development of Filling Imbalances in Hot Runner Molds
Christopher W. White, May 1999
When manufacturing plastic parts from multi-cavity tools by means of injection molding, it is common to use naturally balanced runner systems to deliver the melt to each cavity with identical flow conditions. However, a common occurrence associated with naturally balanced runner systems is that the parts molded in the inner cavities, closest to the sprue, are heavier and larger than the outside parts. Recent studies suggest the inconsistencies be due to unsymmetrical shear distributions created as the melt splits to flow through the various branches of a runner system (1-2). This paper shows the mold-filling imbalances experienced with geometrically balanced runner systems of multi-cavity hot runner molds, through computational fluid dynamics analyses.
The Effect of Phenolic Regrind on the Mechanical Properties of HDPE
Liz Ohlsson, May 1999
The possibility for recycling cured phenolic material was evaluated by testing mechanical properties of High-Density Polyethylene (HDPE) containing phenolic regrind material. The mechanical properties evaluated were: modulus of elasticity, percent elongation, tensile strength, and impact strength. Four different levels of phenolic regrind were used for evaluation with four different levels(4.76, 9.09, 16.7%) of phenolic regrind used in the comparison. The results demonstrated that with higher levels of phenolic regrind in the base HDPE material, certain mechanical properties degraded, with increased brittleness the most apparent effect.
A Study on the Feasibility of Using Granulated Polyvinyl Chloride Coated Fiberglass Screen as a Filler and/or Reinforcement in Specimens Molded from Recycled High Density Polyethylene, Polypropylene,
John Raybuck, Daniel Heuer, May 1999
This paper will analyze the feasibility of using granulated polyvinyl chloride-coated fiberglass screen as a filler and/or reinforcement in injection molded plastic products. The screen, composed of the trim cuts from large rolls and defective sections, will be granulated and blended, in different weight ratios, with recycled high-density polyethylene and polypropylene. The resulting composites will be injection molded to produce ASTM D638 testing specimens. Also, one population of specimens will be produced from a composite of the granulated screen and commingled post-consumer recyclate. The process- ability of the composites and several mechanical properties will be observed and recorded. Statistical methods will be applied to the data, in order to predict the effect of adding different levels of filler/reinforcement on the mechanical properties of the composites.
The Effect of Polyvinyl Chloride and Polystyrene on the Mechanical Properties of Plastic Parts Produced with Commingled Post-Consumer Recyclate
John Raybuck, Daniel Heuer, May 1999
One way to avoid the separation of post-consumer plastic waste is to utilize commingled recyclate in the design of plastic products. However, the combination of many plastic resins can sometimes yield poor mechanical properties, due to the debonding of the different resins. It is important to understand if one or more resins in the commingled material will cause greater debonding than the other resins. This study examines the debonding in low-density polyethylene specimens filled with increasing levels of commingled post-consumer recyclate that does and does not contain polyvinyl chloride and polystyrene. The debonding in the specimens will be characterized through tensile testing.
Processability and Trends in the Mechanical Properties of Low Density Polyethylene Parts Produced Using Increasing Levels of Commingled Recyclate as a Filler
Daniel Heuer, May 1999
As the plastics industry is increasingly confronted with environmental demands and regulations, the need for successful and reliable recycling programs is greater than ever. One of the keys to the success of these recycling programs and to the success of recycled resins is identifying feasible end uses for commingled recycled polymers. One possibility is for plastics manufacturers to specify commingled recycled resins, as a filler, in their products. This can provide savings for the manufacturer, while helping to promote plastics recycling. When specifying the level of commingled recycled resin to be used in a product, the designer must consider the net effect it will have on the processability and the mechanical properties of the part. This study will examine and attempt to predict the net effect of increasing the level of commingled post-consumer and post-industrial recyclate, used as a filler, in the production of low-density polyethylene parts.
Interfacial Interactions in Carbon Fiber Reinforced Epoxy Composites
Béla Pukánszky, János Gulyás, May 1999
The effect of surface coverage and the type of coupling agent were studied in carbon fiber reinforced epoxy microcomposites. The surface of PAN based, electrochemically oxidized carbon fibers was treated with solutions of an epoxy- (EPS) and an aminosilane (AMS), 4,4'-diphenylmethane diisocyanate (MDI) and triglycidyl isocyanurate (TGIC). The amount of coupling agent bonded chemically to the surface of the fiber was determined by analytical methods. Single fiber composites were prepared from treated and non-treated fibers. The fragmentation method was used to determine the interfacial shear strength (IFSS) characterizing fiber/matrix adhesion. The amount of coupling agent bonded to the fiber surface was related to IFSS. A close correlation was found between the bonded coupling agent and adhesion in the case of the epoxysilane and TGIC, but such a correlation could not be found for the aminosilane and MDI.
Interactions of Pesticides and Stabilizers in PE Films for Agricultural Use
Edina Epacher, Béla Pukánszky, May 1999
Polyethylene films used in agriculture are subjected to the effect of oxygen, UV radiation, rain etc. Beside these usual effects encountered in outdoor applications, also the pesticides used for the protection of the crop may influence the degradation and lifetime of the films. In an attempt to determine the interaction of pesticides and some frequently used light stabilizers in PE, films containing three different stabilizer packages were exposed to the effect of 24 commercial pesticide formulations. The effect of UV radiation was modeled by Xenotest aging. The measurement of oxidative stability after exposure indicated that pesticides interact with the stabilizers, indeed. UV and FTIR spectroscopy gave further information about these interactions. Mechanical properties of the films deteriorated considerably after exposure at some pesticide/stabilizer package combinations. According to their effect pesticides could be classified into three groups: inert compounds, formulations with moderate effect and harmful substances. Mainly formulations having sulphur as an active component belonged to this third group due to the activity of sulphur in radical reactions.
Crystallization and Morphology of Propylene/Pentene Random Copolymers
P. Juhász, K. Belina, May 1999
Crystallization and melting behavior of propulene/1-pentene random copolymers were studied. WAXD and d.s.c. measurements of isothermal crystallized samples confirm that the copolymers contain the ? crystal form in large quantity. The content of ? form increases with increasing pentene content and crystallization temperature. We found a limitation in the relative ? content around 60-65%. The efficiency of pentene comonomer is much higher than of ethylene. The equilibrium melting point decreases with pentene content in a non-linear fashion and the values are much lower than the theoretical ones.
Rapid Heating and Curing of Structural Adhesives by Infrared and Radio Frequency
Kin Ming Kwan, Chung Yuan Wu, Avraham Benatar, May 1999
Structural adhesive requires a considerate curing time to achieve handling strength at room temperature. Conventional heating and curing methods are unable to cure adhesives in minutes because of the slow heat input rate to the system. Infrared heating can penetrate into the adhesive to accelerate the reaction process in a very short time. Radio frequency heating produced substantial energy input to the adhesive through the dielectric loss of the polar molecules under rapid changing electric field. The effect of operating parameters on green strength produced from these methods were studied and compared to that cured at room temperature. Both methods show significant reduction in cure time to obtain a strong bond in less than three minutes.
Optimization of Contact Hot Plate Welding of HDPE
Bovornchok Poopat, Chung-Yuan Wu, Avraham Benatar, Joon B. Park, May 1999
The hot plate welding process is widely used for welding of thermoplastics. To optimize the welding processes, melt layer thickness, welding displacement and squeeze-out ratio are used as control parameters. Contact hot plate welding of high density polyethylene (HDPE) was investigated. The melt layer thickness of the high density polyethylene samples during heating was measured. The mathematical relationship between melt layer thickness and hot plate temperature and heating time was developed and used as control parameters. The effects of welding parameters (melt layer thickness, weld displacement and squeeze-out ratio) on joint quality are presented. The results show that the maximum attainable joint strength is 100% of the bulk material strength. A minimum melt layer thickness of 2.5 mm (total from both sides) is required to produce good quality joints. A minimum weld displacement of 0.7 mm (both sides) or a squeeze-out ratio of 0.3 is also required to produce good quality joints.
Hot Plate Welding of Polypropylene and Talc Reinforced Polypropylene Composites
Chung-Yuan Wu, Bovornchok Poopat, Avraham Benatar, Joon B. Park, May 1999
A systematic study of polypropylene and talc reinforced polypropylene using hot plate welding was conducted. The control parameters, welding displacement, melt layer thickness, and ratio of weld displacement to melt layer thickness were studied. A constant pressuring method was evaluated. Approximate equations were obtained experimentally to calculate the melt layer thickness based on the hot plate temperature and heating time. It is found that the maximum joint strength depends on the talc concentration. The maximum joint strength for 0% and 40% talc reinforced polypropylene was 97% and 54% of the bulk strength, respectively.
Rheology of Hard-Metal Carbide Compounds
Berenika Hausnerová, Petr Sáha, May 1999
The results of an investigation of steady-state and oscillatory flow properties of hard-metal carbide powder compounds are presented. These highly concentrated compounds are intended for powder injection moulding (PIM) technology. The volume concentrations of powders, containing mainly tungsten carbide and cobalt alloy, differing in particle size distributions, varied up to 57.5 vol. %. The model relations, correlating relative viscosities with volume fraction of filler and shear rate (shear stress), were used in order to attain maximum volume fraction of powder in the compound. At the concentrations near the maximum loading an unstable flow was observed, which has been found to be influenced by the particle size distribution of the powder used as well as its concentration. In some cases, the instabilities were suppressed by repeated extrusion.
Positive and Negative Electrorheological Effect of Poly(Methyl Methacrylate) Dispersions Stabilized by the Block Copolymer Steric Stabilizer
Vladimír Pavlínek, Petr Sáha, Otakar Quadrat, Jaroslav Stejskal, May 1999
A change of viscosity of the poly(methyl methacrylate) dispersions in decane stabilized with polystyrene-block-poly(ethylene-co-propylene) copolymer after application of an external electric field depends on the character of its original structure. When the mutual particle interactions are low, the organized structure formed in the electric field causes an increase in the viscosity of the dispersion and a positive electrorheological effect appears. If, due to strong interactions, a gel-like network particle structure exists, an application of the electric field causes a breakdown of this structure, the viscosity of the system decreases and negative electrorheological effect occurs. The type of rheological response is thus influenced by composition of dispersions.
Morphology and Compression after Impact Strength Relationship in Rubber-Toughened Composites
B.J. Derkowski, J.A. Avila, S.E. Eschmann, May 1999
Morphology and compression after impact (CAI) strength relationships in rubber-toughened high performance composites are investigated using quantitative image analysis. A group of six quasi-isotropic carbon fiber-epoxy composites, with variations in CAI strength were analyzed to reveal how the particle size, particle size distribution, and location of rubber particles affect the CAI strength values and the corresponding damage mechanisms. It is found that the CAI strength of rubber-toughened composites is greatly affected by the size and size distribution of rubber particles in the interlaminar regions of the composite. In general, high CAI strength composites exhibit more uniform particle size distribution and spread evenly across the interlaminar regions. Whereas, for low CAI strength composites, the rubber particles tend to cluster together and have wide size distribution.
A New High-Performance LLDPE for Blown Film Applications
Harry Mavridis, May 1999
Conventional Ziegler-Natta catalyzed LLDPEs combine good mechanical properties with moderate processability. Efforts to enhance LLDPE properties further, through metallocene catalysts for example, generally result in a processability penalty. The present work describes a new development in LLDPE technology which produces resins with significant improvement in mechanical properties without sacrificing processability. Detailed blown film results show the performance improvement achieved by the new resins, compared to conventional LLDPEs, and the downgauging potential offered by the property improvement.
The Effect of Film Winding Tension and Melt Temperature on COF and Other Properties of PE Blown Film
Brian H. Schumann, Jeffrey J. Wooster, May 1999
A designed experiment has been conducted to determine the effects of sealant layer melt temperature and film winding tension on the coefficient of friction (COF) and other physical and optical properties of a coextruded blown film containing a polyolefin plastomer as the sealant layer. A statistical design program was used to model the quantitative response of the various film properties to the control variables evaluated. Evaluation of the data indicated that only the COF had a significant response to the control variables. As the winding tension of the rolls increased, the COF increased dramatically.
The Use of Polymer Processing Aids to Reduce Gel Formation in Polyolefin Plastomer Extrusion
Susan S. Woods, Stephen E. Amos, May 1999
Polymer additives have long been linked to gel formation and reduction in polyolefin film extrusion. Several hypothesis about these additive/gel links have been empirically explored in a controlled blown film experiment. A study comparing gel levels in a metallocene catalyzed polyolefin plastomer was done on a lab size blown film line with a groove feed extruder. A photo imaging process was used to count gel levels, per unit area, during a significant portion of each run. Additive packages were varied to determine the effect of potential gel reducing additives. The data support the hypothesis that Dynamar™ polymer processing aids can reduce the amount of gel particles in the film.
The Influence of Stress on Peel Strength of Acid Copolymers to Foil
Barry A. Morris, May 1999
As an acid copolymer is converted in the extrusion coating process, it undergoes considerable stress and orientation. This stress arises from shear forces in the extruder and die, from extensional forces as the melt curtain is drawn down and from shrinkage forces during crystallization. It is hypothesized that these stresses may influence peel strength by impacting tensile properties and residual stress at the foil-polymer interface. Relationships are developed between stress and common processing parameters such as air gap, die gap, melt temperature and line speed. An experiment is described where processing parameters were changed in a systematic way to alter the stress imposed on the polymer. Data is presented which strongly supports the hypothesis, and provides an understanding as to the role and impact of various processing parameters.
Munsell Color Science Laboratory Industrial Color Difference Consortium - Current Initiatives and Future Directions
Roy S. Berns, May 1999
There is a continual need for automated approaches to defining color quality within the industrial community. It is well known that color vision is a most complex process with many variables affecting visual color tolerances. Although much progress has been made, as all professionals in this field are likely to agree, much remains to be done. One of the very few such efforts internationally is the RIT Munsell Color Science Laboratory's Industrial Color Difference Consortium, started in 1995. The Society of Plastics Engineers is one of ten members. This paper will summarize recent research and future initiatives.
Automation in Thermal-Analytical Instrumentation and SPC Helps in Supplier Quality
Vijay N. Reddy, May 1999
Defect prevention and reduction of variation are described as minimum expectations in the fundamental quality systems. There are strong relationships between reduction in variation, zero defects and ultimately the cost. Heavy reliance is placed on in-process inspection, testing and on-line monitoring of process parameters. Statistical process controls (SPC) and control charts are used to determine the process capability index (Cpk). Thermogravimetric analysis (TGA) is widely used to measure product quality. We will discuss the use of Robotics-TGA and SPC that has come to the aid of process engineers to improve Cpk in production of polymer based devices for automotive applications.
.jpg)
.jpg)
.jpg)
.jpg)
