The SPE Library contains thousands of papers, presentations, journal briefs and recorded webinars from the best minds in the Plastics Industry. Spanning almost two decades, this collection of published research and development work in polymer science and plastics technology is a wealth of knowledge and information for anyone involved in plastics.
The SPE Library is just one of the great benefits of being an SPE member! Are you taking advantage of all of your SPE Benefits?
Automotive plastics with a low polarity, such as PE,
PP, TPO, POM, PUR and PTFE typically require
surface treatment when decoration is required.
Metallic surfaces may also require cleaning to
remove low molecular weight organic materials
prior to decoration. Once the above-mentioned
interior and exterior grades of substrate surfaces are
cleaned and activated, printing, gluing and painting
are possible without the use of adhesion-promoting
primers. This paper describes the latest innovations
in three-dimensional surface treating technology for
plastics finishing which address the need to advance
adhesion properties, increase product quality, and
achieve environmental objectives within the
automotive industry. These innovations include
advanced thermal and non-thermal discharge
treatment processes for raising the polarity of
surfaces to be painted, bonded, decorated,
laminated, printed, or to have tape applied.
Kalyan Sehanobish | Alexander Chudnovsky | Wen Zhou | Haiying Zhang, November 2011
Using short term tests to predict future outcomes of any long term process is common in extrapolation techniques in Science, Social science and Engineering. However, in every process it is important to ascertain some sort of criterion before extrapolation techniques are employed. The criteria for predicting lifetime of an engineering plastics for the specific application must include the requirements of the test to (a) reproduce the mechanisms of field failures and (b) have a technically sound procedure for extrapolation of a the relatively short test data. We will finally propose a quantitative modeling approach as an alternative to “empirical” extrapolation.
Francesco Caimmi | Roberto Frassine, November 2011
The Mode I and Mode II fracture behaviour of three carbon-epoxy composite laminates with different fabric reinforcement and different matrices was investigated. Standard Double Cantilever Beam (DCB) and End Notched Flexure (ENF) delamination tests were performed to determine initiation toughness and to asses the subsequent crack propagation behaviour. Various toughening mechanism, acting at the microscopic level and responsible for the stick-slip propagation behaviour observed, have been identified. The effect of temperature in a range from -60° to 165 °C was investigated.
Evan Mitsoulis | Thanasis Zisis | Mahmoud Ansari | Savvas G. Hatzikiriakos, November 2011
The capillary flow of a commercial LDPE melt was studied both experimentally and numerically. The excess pressure drop due to entry (Bagley correction), the compressibility, the effect of pressure on viscosity and the possible slip effects on the capillary data analysis have been examined. Using a series of capillary dies having different diameters, D and length-to-diameter L/D ratios, a full rheological characterization has been carried out, and the experimental data have been fitted both with a viscous model (Carreau-Yasuda) and a viscoelastic one (K-BKZ/PSM model). Particular emphasis has been given on the pressure-dependence of viscosity, with a pressure-dependent coefficient βp. For the viscous model, the viscosity is a function of both temperature and pressure. For the viscoelastic K-BKZ model, the time-temperature shifting concept has been used for the non-isothermal calculations, while the time-pressure shifting concept has been used to shift the relaxation moduli for the pressure-dependence effect. It was found that only the viscoelastic simulations were capable of reproducing the experimental data well, while any viscous modeling always underestimates the pressures, especially at the higher apparent shear rates and L/D ratios.
François de Buyl | Vincent Rerat | Christophe Paulo | Scott E. Miller, November 2011
Polypropylene grafting with α,β-unsaturated
carboxylic functional-silanes by melt reactive extrusion
processing in presence of free radical initiator was
demonstrated while preventing significantly undesired
degradation. Such modified PP was then used for enabling
crosslinking into an injected part of neat PP resin, and
enhanced coupling in glass- or cellulose-fibers reinforced
PP composites. After testing composites at high
temperatures (80-120°C), significant improvements were
seen on tensile, flexural, and impact resistances – in
particular stability upon heat, water and oil aging.
Relevance of this work will be discussed against
applications in Automotive, Appliance, and Building
where glass-fibers reinforced polyamide or polyester is
often over-engineered.
This paper is an attempt to predict the flow analysis in the
Maddock kneader using CFD (Computational-Fluid-
Dynamics) method.The effects of three channel of the
kneader have been take in to account in three dimensional
flow analysis.It has been demonstrated that such
computational method can provide a great insight into
visualization of the flow field in this kneader.Among the
variable the barrier flight was found to play a significant
role on enhancing the mixing performance of the
Maddock kneader by means of shear rate distribution in
the channel.
In the last few years the use of plastics as a replacement
of glass has increased many times over. Especially in the
automotive industry more and more panorama roofs and
side windows will be made out of polycarbonate and
PMMA in the near future. Major advantages are a weight
reduction and an improved processability in regards of the
three-dimensionality [1].
The integration of certain functions in these plastic panes
is the next step towards manufacturing innovative plastic
products. This research project is about the integration of
an electrochromic system which is able to change its color
and therefore its level of transparency by applying a
voltage.
Novel phenolic resins (PF) with improved fracture
toughness and flexibility properties were synthesised and
evaluated. A first modification consisted in the
copolymerization of Phenol with a natural renewable
component (Cardanol) during the synthesis of PF resins
(CPF). An increases in the content of Cardanol resulted
in a proportional increases in the flexural strength and in
the fracture toughness together with a decreases in the
flexural modulus of the cured CPF/PF blended resins.
Further increased plasticizing and toughening effect was
observed by the blending of the CPF/PF resins with propylene glycol (PG).
Terje Tofteberg | Jan Peder Hegdal | Age G. Larsen | Trond Schjelderup | Einar L. Hinrichsen, November 2011
A method for rapidly characterizing the shape, size and
distribution of bubbles in foam has been developed. The
method is based on the extraction of bubble shapes from
high resolution images of microscopy slices of the foam,
using image segmentation. The foam studied is the 30 mm
thick high impact polystyrene coating of a thermally
insulated pipe. The coating is applied using extrusion with
a chemical foaming agent and the image segmentation
provides a dataset with the ellipse fit of 500.000 bubbles.
The paper presents a theoretical and, at the same time,
an experimental approach to sheet bending with pads
made of rubberlike materials. Numerical simulation for V
bending was carried out by using the ABAQUS/Standard
software package. The program takes into account the
following: sheet material, pad material, punch stroke and
punch radius. The theoretical results are compared with
experiments in order to determine whether the numerical
simulation is close to reality and whether it gives correct
information about the process even in the area that can’t
be reached by experiments. Some statistical tests were
performed in order to validate the results. Moreover, a
proposal for replacing rubber with plasticized PVC using
two different recipes was made.
The American phrase ‘garbage in, garbage out’ (GIGO for short) succinctly describes a problem often faced by plastics extrusion processors worldwide: No matter how well an extruder extrudes, its output will not be on-spec if the input blend is off-spec. When formulation problems do arise, the on-line proportioning system draws initial troubleshooting focus. But the problem itself (or its underlying cause) may lie elsewhere, farther upstream. This presentation systematically addresses the major process operations prior to extrusion (and beyond to include the materials themselves) in an effort to indentify and avoid the various pitfalls that may plague reliably accurate formulation.
Kazumi Tada | Ayako Watanabe | Hiroshi Ito, November 2011
3-dimensional FEM simulation was performed to
clarify the mechanism on surface replication in
micro-injection molding and thermal nanoimprinting.
Especially the filling behavior into
micro- and nano-surface features was discussed in
comparison with the experimental results. The
simulation results and the experimental results of
injection molding show possibility of the generation
of air traps in the filling stage and it is considered
that those air traps have a strong relation with
replication shape and replication rate. The
simulation results of thermal imprinting clarified
penetration behavior of polymer melt into nanosurface
feature and show that the aspect ratio of the
cavity and imprinting pressure influenced flow
behavior in thermal imprinting.
Cyclic butylene terephthalate (CBT) is a novel thermoplastic matrix material for composites. Besides its low viscosity (0,02 Pas) and superior mechanical properties CBT has some other advantages over conventional matrix materials. During its polymerization no by-product is being made and it is easy to recycle. But processing of CBT is complicated and may results in a brittle material. Polycaprolactone (PCL) as an additive for CBT will also be introduced to increase toughness. In this paper the proper amount of PCL is determined to obtain a ductile material and a method is described how to fabricate prepregs and composites.
Ilhyun Kim | Youngjian Zhao | Byoung-Ho Choi, November 2011
In this study, the effect of various misalignments of the circular notched bar (CNB) specimens on the fatigue crack propagation behavior of pipe grade polyethylene is investigated by three dimensional numerical analyses. The effect of the asymmetric crack growth of the misaligned CNB specimens on the lifetime to failure is also addressed. Two types of misalignments of the CNB specimen, i.e., (a) a concentric misalignments (Case I) and (b) an angular misalignments (Case II), are considered using finite element analysis. It is observed that as the misalignments increase, the asymmetric crack growth is accelerated so that the time to reach the critical SIF decreases. Therefore, it can be understood that the lifetime to failure of CNB specimens can vary noticeably once the CNB specimen is misaligned initially. Considering results from this study, the fatigue crack growth behavior including the estimation of the lifetime of CNB specimens should addressed by considering the misalignment effects.
The present work attempts to implement reactive compatibilisation of blends of recycled engineering plastics, more particularly the case of recycled PA66 contaminated by recycled PA6. Low molecular weight, high Tg Styrene-Maleic Anhydride copolymers were tested as chain extenders / compatibilizers. It appeared that the addition of 2% by weight of SMA to an incompatible system of recycled PA6 and PA66 improved both ductility and impact performance by factors of at least 10 and 1.5 respectively. Moreover, high Tg SMA improved performances at elevated temperature, partly due to its ability to effectively crosslink but also because of its inherent heat resistance.
Manoranjan Prusty | Martin Baumert | Martin Völker | Tobias Nachtigaeller | Susanne Gruber | Dietmar See | Wolfgang Seib | Harald Kroeger | Walter Rau | Hans-peter Beringer | Willy Bert Hoven Nievelstein, November 2011
New Ultramid® Endure from BASF is the first of its kind
PA66 based polymer which has excellent heat ageing
resistance,welding strength after heat ageing and good
processing properties. Ultramid® Endure can withstand
continuous use over 3000 hours at 220°C and temperature
peaks upto 240°C. The excellent heat ageing properties of
Ultramid® Endure allows it to be used for applications
such as resonator, charge air lines etc.
Poly(o-aminophenol) (POAP) films were deactivated and then reactivated, and dependences of the different charge-transport and charge-transfer parameters on the degree of deactivation (c) were obtained by employing Electrochemical Impedance Spectroscopy. These dependences were extracted when the polymer contacts an electroactive solution and a mediation reaction occurs at the polymerelectrolyte interface. While some parameters, such as interfacial metal-film and film-solution resistances (Rmf, Refs, Rifs), the high-frequency capacitance (CH) and the redox capacitance (Cp) exhibit a continuous variation without hysteresis between deactivation and reactivation processes within the whole c range, others, such as electron and ion diffusion coefficients (De, Di), show hysteresis between consecutive deactivation and reactivation processes. On the basis of these findings it was considered that while some parameters of the polymer only depend on the amount of redox active sites, others (De and Di) depend on both the quantity and distribution of redox active sites.
André J.P. van Zyl | Robert D. van de Grampel | Theo L. Hoeks, November 2011
With the progression of technology, increasing
pressure is put on engineering plastics companies to fulfill
strict design criteria of equipment manufacturers.
Therefore novel materials are needed to address specific
needs. The most common method to manipulate material
performance is by either blending or an additive approach.
Although relatively cost-effective and requiring low
technological input, these methods are not always desired
due to the potential incompatibility of blends and/or nonpermanence
of additives. In this paper a copolycarbonate
approach will be discussed to address specific consumer
needs. More specifically the tailoring of properties from a
molecular perspective will be discussed and examples
showed of how copolycarbonates can be used to capture
novel markets.
Frank Yepez Castillo | Brian P. Grady | Daniel E. Resasco, November 2011
Multi-walled carbon nanotube/high density polyethylene composites with varying amounts of carbon nanotubes were processed in an extruder fitted with a low-shear adaptor. This equipment allowed annealing of the melt for various amounts of time under low shear before it was passed through a slit die. The effect this treatment had on the electrical and mechanical properties of the composites was investigated. Results obtained from extruded samples were compared to the mechanical and electrical properties of samples that had been mixed in a micro-compounder and compression molded. Differences in the crystallinity and the orientation of extruded samples were also assessed.
Zhenwen Zhou | Alexander Chudnovsky, November 2011
A number of water utilities in various states of USA have reported a persistent premature failure of polybutylene (PB) tubing in water distribution system. Failure analysis of PB system and a methodology of reliability analysis of PB tubing in potable water application are presented in this paper. The reliability analysis allows predicting future failures. Thus, the proposed methodology is validated by comparison of failure prediction with actually reported field failures in selected water districts from Maryland, Georgia and Ohio. The proposed methodology also allows a rational replacement planning by considering the effect of preventive replacement program on the reduction of emergence replacements. Understanding of main PB failure mechanisms in potable water application important for proper interpretation statistics is also discussed.
84 countries and 60k+ stakeholders strong, SPE
unites
plastics professionals worldwide – helping them succeed and strengthening their skills
through
networking, events, training, and knowledge sharing.
No matter where you work in the plastics industry
value
chain-whether you're a scientist, engineer, technical personnel or a senior executive-nor
what your
background is, education, gender, culture or age-we are here to serve you.
Our members needs are our passion. We work hard so
that we
can ensure that everyone has the tools necessary to meet her or his personal & professional
goals.
Any article that is cited in another manuscript or other work is required to use the correct reference style. Below is an example of the reference style for SPE articles:
Brown, H. L. and Jones, D. H. 2016, May.
"Insert title of paper here in quotes,"
ANTEC 2016 - Indianapolis, Indiana, USA May 23-25, 2016. [On-line].
Society of Plastics Engineers
Available: www.4spe.org.
Note: if there are more than three authors you may use the first author's name and et al. EG Brown, H. L. et al.
.jpg)
.jpg)
.jpg)
.jpg)
