The SPE Library contains thousands of papers, presentations, journal briefs and recorded webinars from the best minds in the Plastics Industry. Spanning almost two decades, this collection of published research and development work in polymer science and plastics technology is a wealth of knowledge and information for anyone involved in plastics.
The SPE Library is just one of the great benefits of being an SPE member! Are you taking advantage of all of your SPE Benefits?
Fiber jamming is perhaps the least understood defect in molding of polymer composites. This paper presents a dimensional analysis developed to predict fiber distribution in ribbed sections. The model shows that parameters like mold closing speed and polymer viscosity can be optimized to decrease fiber matrix separation.
The influence of a stress concentrator on the mechanical properties of injected plastic parts was studied. Polystyrene plaques with different dimensions of a triangular concentrator were injected. Melt temperature, injection and holding/packing pressures and injection speed were modified in order to determine their influence on the stress concentrator factor (Kt). The experimental results were compared with the simulation ones. It was verified that Kt depends on geometrical parameters and process conditions of the injected plastic parts.
M.V. Candal, A. Gordillo, G. Terife, O.O. Santana, May 2007
The effect of the injection molding process conditions (melt and mold temperatures, holding/packing pressure and injection velocity) over the adhesion resistance of two overmolded materials was studied. The materials used were a Thermoplastic Vulcanized Elastomer (TPV) (Santoprene 8211-55) and a Polypropylene (PP) (Moplen HP501H). The measurement of the adhesion resistance was done by Tensile Test and it was observed that the melt and mold temperature are the parameters that affect in greater degree the adhesion resistance.
Jonathan Jeffery Stanger, Nick Tucker, Nigel Larsen, Mark Staiger, Roger Reeves, May 2007
For large-scale application of electrospinning technology, it is important to know how to maximise and control the deposition rate of spun fibre. Driving polarity, substrate material and current flow were examined to quantify their effect on fibre deposition rate. Conductivity of the substrate and polarity of driving electric charge were found to affect the mass deposition rate. Higher deposition rates were the result of the production of thicker fibres and an increase in deposition speed.
The part properties are determined by quality of gas penetration in gas-assisted injection molding (GAIM), while processing conditions determine gas penetration. This research aimed to investigate some of the processing parameters, such as shot size, gas delay time and gas pressure. The effect of processing parameters on shrinkage ratio was discussed, as well as that how they influenced the part performance.
A new injection technique for introducing physical blowing agents into molten polymer is studied for its application in foam extrusion. Therefore, a special injection device is mounted on a standard laboratory scale single screw extruder. By means of this device, CO2 is injected into PS melt. In this paper first results of these preliminary tests are shown. The foams produced with this new technique exhibit a cell size in the range of 100 microns.
In the blow molding process, the blown part is primarily cooled by contact to the mold. Using internal cooling it is possible to reduce the cooling time. Using atomized water, is a new method to increase the heat flow at the internal surface. At the IKV the blow mandrel and the blow molding machine are modified to inject atomized water. The achievable cooling time reduction depends on the amount of the injected atomized water. The test series show that a reduction of cooling time up to 41% is achievable.
The anisotropic material behavior of injection-molded, short-fiber reinforced thermoplastic parts can be taken into account in mechanical simulation today by linking process simulation and structural analysis. However, the prediction of the crashworthiness of short-fiber reinforced parts is still performed predominantly using isotropic material models as a substitute. An approach to include anisotropic material behavior into crash-simulation has been developed at the Institute of Plastics Processing in order to advance simulation quality.
Wood fibers are often used to reinforce polyolefins but not high temperature polymers like polyamide 6 and 66. These polyamides melt above 200 °C, which is often considered the maximum processing temperature for wood fibers. A variety of techniques for compounding and molding wood fiber/polyamide composites will be presented. These techniques are evaluated by examining fiber dispersion, fiber attrition and composite mechanical properties.
Walter Michaeli, Manfred P. Hentschel, Oliver Lingk, May 2007
A new method to determine the specific volume of polymers over a wide range of temperature and pressure based on X-ray attenuation was developed. This method allows the application of different cooling rates enabling the investigation of the density depending on the thermal history. Experiments were performed to investigate the devolution of the specific volume of an isotactic polypropylene at elevated pressures and cooling rates.
M. Zatloukal, K. Chaloupkova, D. Hertel, H. Münstedt, May 2007
The vortex development of a low-density polyethylene in different flat dies under various processing conditions has been analyzed by the Finite Element Method employing the modified White-Metzner model as constitutive equation. The theoretical results are compared with the velocity distributions measured by Laser-Doppler Velocimetry (LDV).
The DataPaq Rotomolding Telemetry System in conjunction with the Medkeff/Nye Shuttle PD developmental rotational molder was used to study and monitor internal mold and oven temperatures. Continuous internal temperature readout along with the software package were used to optimize the cycle of linear low density polyethylene (LLDPE). Designed experiments were employed to investigate process parameters and select physical and mechanical properties.
A novel single screw mixer is described having multiple elongational flow fields, upstream axial mixing, and thin film degassing. SEMs show high magnification examples of mixing including a PS/PE immiscible polymer blend, ceramic nano particles, and iscrete carbon nano tubes. Novel degassing over the mixer is cited using three vents in a 36/1 L/D single screw to process undried PETG.
W.-J. Boo, L. Y. Sun, S.-M. Lee, E. Moghbelli, G. Warren, A. Clearfield, H.-J. Sue, May 2007
The structure-property relationship of a set of model polymer nanocomposite systems has been investigated. The findings suggest that degree of exfoliation and aspect ratio of nanoplatelets in polymer matrices can greatly influence physical, mechanical and rheological behaviors of polymers. Most importantly, there appears to be a limit to which polymer nanocomposites can be applied for structural applications.
The effect of long chain branching in polyvinylidene fluoride in extrusion blow molding is investigated in light of the enhanced rheological properties. The presence of long chain branching increased the melt strength; melt elasticity and strain hardening of the branched samples as opposed to their linear counterparts. These enhanced properties suggest better sag resistance during blow molding and higher blow-up ratio while achieving uniform wall thickness.
3D injection molding analysis is getting popular to get accurate result in the industry. However, mesh generation time and memory size for complex models are being demanded more than those of general model or conventional 2.5D analysis. This paper adopts simulation technology such as CVFEM(Control Volume Finite Element Method) or fast multipole method based on BEM(Boundary Element Method) and shows real case for large models. It does not only develop effective method to reduce modeling time, but it also performs analysis with significant performance enhancement.
Blow moulding simulation softwares are effective tools for blow moulders to predict and improve the performance of blow moulding process. Not many such software are available in the market. This paper presents a comparative study of two blow moulding software - B-SIM and Blow View – for specific application of stretch blow moulding process. Features and capabilities are compared based on the simulation study of a plastic bottle.
This paper addresses the design issues and processing conditions that affect the performance of integral hinges. For example, the relation between the material properties and the design of the hinge is addressed. An answer will be given to the question why does the increase in the melt temperature improve the performance of hinges?" Some case studies of failed hinges are discussed to practically show the effect of processing material and design on hinges performance. Microscopy was used to investigate the failure mechanism of these hinges."
The effect of die design and wall slip on the die drool phenomenon was investigated for metallocene based LLDPE. It has been found that die exit opening and wall slip can significantly reduce the die drool phenomenon. Moreover, theoretical research has revealed that die drool onset can be explained by the negative/non-monotonic pressure profile generated inside the die and/or at the die exit region due to melt elasticity.
In this work, specially designed zero-length dies were used for the entrance pressure drop measurements with the aim to determine uniaxial extensional viscosity of polyolefin melts by using effective entry length correction and Cogswell/Binding models and the results were compared with the extensional rheology determined with the Sentmanat extensional rheometer. Reasonable agreement between these two techniques has been obtained.
84 countries and 60k+ stakeholders strong, SPE
unites
plastics professionals worldwide – helping them succeed and strengthening their skills
through
networking, events, training, and knowledge sharing.
No matter where you work in the plastics industry
value
chain-whether you're a scientist, engineer, technical personnel or a senior executive-nor
what your
background is, education, gender, culture or age-we are here to serve you.
Our members needs are our passion. We work hard so
that we
can ensure that everyone has the tools necessary to meet her or his personal & professional
goals.
Any article that is cited in another manuscript or other work is required to use the correct reference style. Below is an example of the reference style for SPE articles:
Brown, H. L. and Jones, D. H. 2016, May.
"Insert title of paper here in quotes,"
ANTEC 2016 - Indianapolis, Indiana, USA May 23-25, 2016. [On-line].
Society of Plastics Engineers
Available: www.4spe.org.
Note: if there are more than three authors you may use the first author's name and et al. EG Brown, H. L. et al.
.jpg)
.jpg)
.jpg)
.jpg)
