The SPE Library contains thousands of papers, presentations, journal briefs and recorded webinars from the best minds in the Plastics Industry. Spanning almost two decades, this collection of published research and development work in polymer science and plastics technology is a wealth of knowledge and information for anyone involved in plastics.
The SPE Library is just one of the great benefits of being an SPE member! Are you taking advantage of all of your SPE Benefits?
Online Raman spectroscopy was used in this study to measure the orientation development during blown film extrusion of low-density polyethylene (LDPE). The analysis is valid for uniaxial symmetry of the structural units with the chain axis. The trans C-C stretching vibration of PE at 1130 cm-1, whose Raman tensor is coincident with c-axis of the orthorhombic crystal, was used to solve a set of five intensity ratio equations. Crystalline orientation (P2) was found to increase along the axial distance in the film line. The P2 values also showed an increasing trend with crystalline evolution during extrusion
The effect of the number laminated oriented PE film (Tyvek) for use in the development of light weight armor and a device for testing its ballistics characteristics were evaluated. The study showed that Tyvek is oriented in the longitudinal direction ± 45° along the X-axis. The number of laminates appears to be critical ballistic characteristics. The higher the number of layers the shallower the penetration of the dart. For example with 6 layers, the penetration was 0.003 m for the long tube, and 0.001m for the short tube. This is because Tyvek is oriented in the longitudinal direction, and also the manner in which the layers are compression molded: biaxial or parallel has an effect on the ballistic characteristic.
The electrical properties of blends of thermoplastic polymer, inherently conductive polymer (ICP) and metallized carbon fiber were studied. Both electrical resistance and electromagnetic shielding effectiveness were measured. These results were compared with the data for blends of thermoplastic polymer and metallized carbon fibers. The electrical resistance of the blends with ICP was much lower than that of the blends without. Additionally, the magnitude of the shielding effectiveness for the blends with inherently conductive polymer was higher than the blend without. The shape of the curves was different, as well, particularly at lower frequencies.
Cavity pressure has been found to be a reliable process indicator in injection molding for both part quality and process monitoring. Specifically, it has been found to provide real-time detection of part and process deviation. As such, cavity pressure measurement holds potential for monitoring part quality in micro-injection molding where direct part inspection is difficult due to part handling issues and microscopic feature sizes. The goal of this study is to determine the feasibility and robustness of using cavity pressure for process and quality monitoring of a molded hollow cylindrical cap. Although the processing window for micro-injection molding was smaller, the different shapes of cavity pressure curves showed that the pressure was able to respond differently to different molding conditions.
H. Jiang, R. Browning, A. Moyse, H.-J. Sue, May 2007
Surface texture/roughness is necessary for various engineering applications of plastics. Their effects on scratch performance have to be examined. Random animal skin surface was studied and compared against the smooth surface counterpart. It is found that of the animal skin surface can delay the onset visibility. To study the effect of surface roughness on scratch resistance, samples with controlled surface roughness were prepared to compare against the smooth and random animal skin surface samples. Rougher surfaces exhibit a lower friction coefficient and a better scratch performance. Approaches for improving scratch resistance of polymers via control of surface texture/roughness are discussed.
Mathew D. Rowe, Erin M. Smith, Keisha B. Walters, May 2007
The goal of this research is to develop biodegradable copolymers from biomass-derived starting materials. The monomers, 1,3-propane diol and malonic acid, were selected based on the presence of reactive functional groups and availability of these materials in biomass. The effects of varying catalyst and temperature on polymer yield were determined. FTIR spectroscopy and nuclear magnetic resonance (NMR) were used to confirm polyester synthesis. The polymerization yields, using aluminum chloride, tin(II) chloride, and iron(III) chloride as the catalyst, ranged from 18-58%, 20- 43%, and 32-47%, respectively, over the 125-175 ºC reaction temperature range.
David J. Gomolka, Daniel F. Yasenchak, Paul R. Minbiole, May 2007
The electron beam irradiation of polymers can bring about various property improvements. The interaction between energized electrons and materials result in valuable reactions, the two most important reactions being crosslinking and chain scission. These modifications to the molecular structure of the materials are characterized by improvements to the mechanical and physical properties of the materials. A number of case studies have been completed involving the electron beam irradiation of various materials and the creation of innovative products. The paper will discuss the various studies and present the associated data.
The effect of thermally conductive particles on the thermal properties of silicone rubber was studied. Different sized aluminum oxide was blended with addition cured silicone resin at various crosslink densities and filler loading levels. Thermal impedance of each sample was measured. Statistical analysis of the experimental data showed that hardness was not affected by filler type/size or filler amount; however, the amount of crosslinker was statistically significant with respect to hardness.Thermal impedence was affected by crosslinker and filler amount in a statistically significant way. As the filler particles are more conductive than the polymer, the greater the amount of filler present, the higher the composite conductivity. Deformation of the material during the test was found to influence the results of the testing.
Laser marking and engraving for the automotive industry poses many challenges to the plastic mold manufacturer. In the past, laser-marking systems have not been intuitive in confirming part identification or part positioning. Inaccurate placement of the mark due to a part misalignment or the engraving of incorrect marking information due to a lack of part identification results in waste parts and reduces product profitability in a highly competitive market.This paper describes the procedure for laser marking using a through-the-lens vision process, Integrated Mark Positioning (IMP), and data compiled comparing marking with and without IMP. Results show that a mark placement accuracy of 0.03 mm with a part placement variation of 4 mm or larger can be achieved. System configuration, operation and benefits of integrated vision are also covered.
Gang Zhou, Siva Movva, Dante Guerra, L. James Lee, May 2007
In this paper, a novel manufacturing method was used to prepare the hybrid composite, wherein nanoparticles were sprayed and bonded onto fiber mats instead of mixing them in polymer resin. The effect of nanoparticles on the mold filling characteristics in a vacuum assisted resin transfer molding system was investigated. This study seeks to understand the flow of resin through the porous fiber bed, consisting of the long fibers and nanoparticles. A simplified model was used to predict the mold filling time. It was found that the dispersion and loading of the nanoparticles affected the permeability and porosity of the reinforcement system, and hence the mold filling time.
This study assesses micro-feature replication at elevated mold temperature and ambient pressure using a variety of polymers and commonly used mold surfaces. In order to more fully explore the micro molding processing window, the effect of one end of processing condition i.e application of only high temperatures was studied. Molding trials were performed on micro and nano featured mold surfaces at elevated mold temperatures and ambient pressure. Feature replication was analyzed quantitatively using an atomic force microscope, comparing the attained depth of the polymers for different aspect ratio features. A qualitative and dimensional analysis was also performed by field-emission scanning electron microscope. Crystallinity of the polymers in the molded parts was attained by X-Ray Diffractometer. While feature detail was well replicated for all the polymers, the moldings exhibited poor dimensional accuracy due to high shrinkage in the parts. In general, polymers with low crystallinity showed the best feature replication.
Arron M. Strepka, William D. Arendt, Makarand Joshi, May 2007
Plasticizer blends are commonly utilized to develop the desired processing and performance properties in flexible vinyl. To increase processing speeds, high solvating phthalates are typically included in these blends. Benzoate esters are high solvating plasticizers that can also be utilized for this purpose. However, the benzoate esters are not drop-in replacements for phthalates and other properties can be affected. An example of this is the increased viscosity commonly experienced in plastisols. The purpose of this paper is to demonstrate the use of designed experiment software to optimize the composition of general purpose and high solvating benzoate plasticizer blends to obtain all desired properties. A resilient flooring plastisol formulation was selected as the model. The following properties were measured on the plastisol: degassing, plastisol viscosity over a range of shear rates, viscosity stability of the plastisol and gelation/fusion characteristics. Stain resistance and tensile properties were evaluated on the fused vinyl film. The data will demonstrate the use of DOE software to develop an optimized plasticizer package that will deliver the desired balance of properties in an efficient and timely manner.
The oxidation kinetics of unstabilized polypropylene (PP) was analyzed by isothermal thermal gravimetric analysis (iTGA). Oxygen incorporation led to an initial weight gain before a dramatic decrease in weight as confirmed by Fourier Transform Infrared Spectroscopy (FTIR). The weight loss was attributed to the release of low molecular weight oxidation products. The time until the onset of weight gain as a function of temperature was used to determine the activation energy for the oxidation reaction. For PP the activation energy was determined to be 155kJ/mole. Literature values differ from this number from -28% (1) to 55%(2).
Joel R. Bell, Carlos R. Lopez-Barron, Christopher W. Macosko, May 2007
Cocontinuous morphologies, distinguished by the mutual interpenetration of two polymer phases, allow for enhanced mechanical properties, static charge dissipation, and barrier properties. Compatibilizers, e.g. block copolymers (bcp), are often added to hinder phase coarsening in blends of immiscible polymers and can improve adhesion at interfaces. We have studied the effect of bcp on the cocontinuous morphology of polystyrene (PS)/polyethylene (PE) and PS/poly (methylmethacrylate) PMMA model blends using scanning electron microscopy (SEM) with image analysis, 3D synchrotron x-ray microtomography, mercury porosimetry, solvent extraction, and rheology. We have shown that an optimal bcp suppresses coarsening in these blends and widens the range of cocontinuity.
Shear induced variation effects have been shown to cause imbalances in filling patterns in both single and multi-cavity molds. These effects, however, extend beyond just the way a cavity fills and can attribute to the way a part cools and warps. Neat and filled materials vary in shrinkage and warpage properties but both are affected by shear induced melt variations developed in the runner section. Using the somewhat opposite" shrinkage properties of a neat and fiber filled material will allow for an in depth understanding of how shear variations will affect materials with and without fillers during and after molding."
Ionic Polymer-Metal Composites or IPMCs, are one type of electroactive polymers that display remarkable shape-altering properties. Most IPMCs are made up of a polymer membrane contained within metal electrodes, which are typically gold or platinum. When an IPMC is hydrated, counter-ions can move freely away from stationary anions toward an electrode when an electric current is induced. This is due to the hydrating liquid’s effect of solvating the cation. The result is the IPMC’s deflection toward the anode. IPMC membranes have advantages over traditional actuators in the fact that they lack moving parts and require very small voltages to operate.
Melt strength or strain hardening of the melt in elongational flow is important for a variety of polymer processing operations. The effect of varying surface treatment on the montmorillonite was investigated in composites prepared with 5 wt% of differently treated clays and a functionalized polypropylene alone as the matrix. The strain hardening behavior in extensional flow was evaluated with the EVF attachment on the TA-ARES rheometer. While the dispersion was better with the primary amine treated montmorillonite, the nanocomposite with the two alkyl tail quaternary ammonium ion showed dramatically improved strain hardening.
For the majority of composites and their intended applications, the transfer of stress from the point of application throughout the remainder of the composite structure is by a shearing mechanism. The interface between fiber and matrix therefore, plays a major role. This paper examines the drawbacks from conventional micromechanical testing of model composites and introduces the benefits of fragmentation testing of aramid fibers in a thermoplastic elastomer matrix using Raman spectroscopy. Accurate and precise measurements of the interfacial shear strength between fibers and matrix are attainable.
The glass transition behavior of poly(?-methyl styrene), its tridecamer, and an athermal blend with its hexamer is investigated using differential scanning calorimetry. The glass transition, Tg, of the blend is found to become broader than that of the pure materials. However, the absolute heat capacity of the blend remains unchanged. The length scale of the cooperatively rearranging regions of the samples, as well as previously studied pentamer, polymer, and blends, is estimated from Donth's fluctuation model. The broadening of Tg is found to accompany a decrease of the length scale. In addition, the correlation between Tg, fragility, and the length scale of CRR is also examined.
Shape Memory Polymers (SMP) blends are of particular interest because they are easily processible, commercially available and recyclable. In this paper we study blends of PVDF (semi-crystalline, Tg=-35 °C, Tm=173 °C) and PVAc (amorphous, Tg=33 °C) which are miscible at all blending ratio (presence of a single Tg). Effects of composition as well as thermal histories on crystallization were investigated via differential scanning calorimetry (DSC), parallel plate rheology and polarizing optical microscopy (POM). For the first time, evidence for two distinct crystalline forms was observed in a blend with PVAc and PVDF crystallized for all blending ratios. Rheological measurements show that the rubber plateau of the blend decreases with lower PVDF content because of lower density of physical crosslinks. Surprisingly, in the case of 30:70 PVDF:PVAc the highest rubber plateau was achieved by isothermal crystallization at temperature close to, but above, the crystallization point measured by DSC. Comparing rheological and optical results for crystallization kinetic, it can be inferred that PVDF crystallizes faster near a solid interface than in the bulk.
84 countries and 60k+ stakeholders strong, SPE
unites
plastics professionals worldwide – helping them succeed and strengthening their skills
through
networking, events, training, and knowledge sharing.
No matter where you work in the plastics industry
value
chain-whether you're a scientist, engineer, technical personnel or a senior executive-nor
what your
background is, education, gender, culture or age-we are here to serve you.
Our members needs are our passion. We work hard so
that we
can ensure that everyone has the tools necessary to meet her or his personal & professional
goals.
Any article that is cited in another manuscript or other work is required to use the correct reference style. Below is an example of the reference style for SPE articles:
Brown, H. L. and Jones, D. H. 2016, May.
"Insert title of paper here in quotes,"
ANTEC 2016 - Indianapolis, Indiana, USA May 23-25, 2016. [On-line].
Society of Plastics Engineers
Available: www.4spe.org.
Note: if there are more than three authors you may use the first author's name and et al. EG Brown, H. L. et al.
.jpg)
.jpg)
.jpg)
.jpg)
