The SPE Library contains thousands of papers, presentations, journal briefs and recorded webinars from the best minds in the Plastics Industry. Spanning almost two decades, this collection of published research and development work in polymer science and plastics technology is a wealth of knowledge and information for anyone involved in plastics.
The SPE Library is just one of the great benefits of being an SPE member! Are you taking advantage of all of your SPE Benefits?
David O. Kazmer, Peter Knepper, Stephen Johnston, May 2005
A survey of commercially available and broadly used pressure and temperature sensors for injection molding is presented. The various pressure and temperature sensing means are reviewed along with the geometry and performance of common transducers. Usage and trade-offs in sensor design and selection is discussed.
A simple equation with only a few physical parameters for the description of the high stalk bubbles has been derived from variational principles. The proposed equation was used in modeling of the film blowing process and a very good agreement between measured and simulated data was found.
M. Zatloukal, W. Kopytko, J. Vl?ek, P. Sáha, May 2005
Modified Leonov model has been used for the viscoelastic stress calculation in the flat multi-manifold coextrusion die used for LDPE film casting process. It has been shown that specific type of high stress area occurs around the interface at the end of the converging section. This total stress has been found to be nonmonotonic along the interface and related for the onset of zig-zag type of interfacial instabilities when the total stress achieved 200 kPa.
Mathew Raymond, Andrea Leczynski, Jason Iovanna, Amad Tayebi, May 2005
In this paper, process and film parameters affecting the peel strength of impulse heat sealed thermoplastic polymeric films are investigated. In particular, the roles of film thickness and duration/temperature of application of impulse heat sealing tool are investigated for low density polyethylene. The data obtained are particularly useful in flexible packaging and film sealed container applications.
R.A. Morales, S.L. Villarroel, D. Garmendia, May 2005
The objective of this work was to evaluate mechanical properties of a cellular phone. Evaluation was made employing two commercial simulation programs. Acting bonds and external forces to simulate the phone opening action were determined. Programs used were capable of modeling static loads for the stress analysis by finite element mesh creation. Maximum wall shear stress and residual stresses showed maximum values in the gate area, in smaller thickness sections.
The study investigates the high deformation and resulting high strains occurring during the flex of living hinge designs by putting a finite element model through the full range of motion. It investigates the ability of this technique to predict feature alignment after fully closing by comparing to actual molded parts. It investigates the feasibility of obtaining accurate simulation results from a model that undergoes high element distortion and material model at very high strains.
M T Martyn, R Spares, P D Coates, M Zatloukal, May 2005
Flow visualisation studies were preformed to determine process parameters initiating interfacial instability in the coextrusion of polyolefin melts. Slit coextrusion visualisation cells with 30° and 90° convergent streams were studied. Studies were performed using two different extruder arrangements. Stress fields, quantified using birefringence. Concomitant velocity and layer ratios leading to wave type interfacial instability in the polyolefin melts are presented.
R. Tchoudakov, E. Segal, M. Letuchy, M.Narkis, A. Siegmann, May 2005
Sensors produced as extruded filaments based on HIPS/ABS/CB and HIPS/LLPE/CB blends were exposed to ethanol, acetone, heptane and benzene. The solubility parameters of the liquid and the blend components are important in determining the sensing level. Sensors based on proper immiscible polymer blends exhibit reproducible and recoverable electrical resistance behavior upon exposure to liquid/ drying air cycles, selectively responding to different liquids or liquid mixtures of different ratios.
M. Zatloukal, M.T. Martyn, P.D. Coates, J. Vl?ek, May 2005
Fully viscoelastic FEM together with flow visualization technique are employed to quantify the effect of the die design on the wave type of interfacial instabilities in coextrusion. It has been shown experimentally that the minor channel geometry has a strong impact on the wave type of interfacial instabilities and the results can be correlated through novel criteria called as Total Stress Difference (TSN), which takes in to account the bulk change of the total stress in normal as well as tangential direction with respect to the interface.
The FCBGA can have the advantages of flip chip and BGA to provide the needs of high-speed networking and telecommunications systems. This study tries to predict the accumulated warpage of FCBGA throughout the sequential packaging process. Since IC device is packaged by several kinds of materials with dissimilar properties, the methodology of death-and-birth is used to simulate the existence of components at each stage. The results show similar trend with the experimental verification.
M. Hernández, M.N. Ichazo, C. Albano, J. González, May 2005
Rheological and mechanical behavior of EPDM rubber filled with woodflour was studied based on blend ratio and curing systems. Irradiation was also studied as an alternative crosslinking method. Results indicate that woodflour accelerates rubber vulcanization. When comparing curing systems, final overall vulcanizates properties did not deteriorate with the efficient system. Concerning irradiation, an optimum dose of 110 kGy was found, since lower doses do not promote crosslinking and higher doses tend to decrease overall properties.
Guangjian He, Jingping Qu, Xianwu Cao, Xiangfang Peng, May 2005
A novel dynamic capillary rheometer (DCR) was designed to investigate the viscoelastic characteristic of polypropylene melt. The pulsatile flow of polymer melt could be got by parallel superposition of oscillation on steady shear flow in this novel DCR. The vibration frequency-dependent behavior of the phase angle and the shear stress vs. shear rate loops can be determined during pulsatile extruding processing. With the increase of the vibration frequency, the elastic characteristic of PP melt becomes more apparent.
Yung-Yuan Wang, Chi Chung Hsu, Rong-Yeu Chang, May 2005
The analysis of encapsulant flow during under-fill encapsulation would be discussed in this work. With solving the melt-front positions based on 3D Finite Volume Method, we get better predictions than 2.5D simulation. For the surface effects among encapsulant, bumps and substrate, the results illustrate that the variations of contact angle influence filling time greatly. Moreover, by applying approximated parameters of dynamic contact angle model, we can simulate the influence of different processing conditions on filling time predictions.
Electroplating PC/ABS requires the plastic be conditioned through “etching” where metal is interlocked into the part. This only occurs when the part has a butadiene-rich surface. Not achieving this condition results in costly unrecoverable plated scrap. In this study, the injection molding process effect on plating scrap was studied where it was learned that the slower the injection rate provides less plating scrap, contrary to traditional molding efficiency.
Moshe Favelukis, Olga M. Lavrenteva, Avinoam Nir, May 2005
The influence of inertia on the deformation and breakup of a slender bubble embedded in a Newtonian liquid in an axisymmetric extensional flow has been theoretically studied. The steady-state problem is governed by two dimensionless parameters: The capillary number and the Reynolds number for the external flow. The calculated stationary deformation reveals the existence of multiple solutions. A stability analysis of these results is used to distinguish between stable and unstable solutions and to establish the break-up point.
New slip model based on ‘effective continuum methods’ for the description of slip was developed and used for investigation of process aids effect on the zigzag type of interfacial instabilities in coextrusion flow.
Anne-Sophie Lichtlé, Laurence Meylheuc, Dmitry Kucharavy, Emmanuel Caillaud, May 2005
One of the major difficulty in designing extruded structures consists in understanding and managing their driving parameters like: material structure;process characteristics;their system effects; which influence the shock resistance. Thus, it is proposed to identify these relationships within the context of redesigning the PVC pipes for sewer systems.
Selective laser sintering (SLS) with CO2 lasers is only used commercially with polyamide (PA) and polystyrene (PS). This is because only these polymers absorb enough energy to melt properly in the SLS process.In a new approach, carbon black is added to the thermoplastic polymer powder. Carbon is sensitive to the wave length of Nd:YAG lasers and can absorb enough energy that adjacent polymer melts.In this paper a feasibility study of this new method is presented. As an example the sintering behaviour of the high temperature resistant polymer polyether ketone (PEK) is shown.
Using a mold specifically designed for the purpose of studying Width-to-Thickness Ratios in grill shaped geometry, parts are molded at each of four different width-to- thickness ratio settings using a control ratio of 10:1 in each setting. Semi-crystalline and amorphous behavior is investigated.
Y. Sun, M. Gupta, J. Dooley, K.A. Koppi, M.A. Spalding, May 2005
The flow in a flat die is simulated using the axisymmetric and planar elongational viscosities of a low-density polyethylene (LDPE) resin. Elongational viscosity is found to have only a limited effect on the velocity distribution at the die exit. However, the predicted pressure drop in the die increased when the effect of elongational viscosity is included in the simulation. Predicted pressure drop is compared with the corresponding experimental data.
84 countries and 60k+ stakeholders strong, SPE
unites
plastics professionals worldwide – helping them succeed and strengthening their skills
through
networking, events, training, and knowledge sharing.
No matter where you work in the plastics industry
value
chain-whether you're a scientist, engineer, technical personnel or a senior executive-nor
what your
background is, education, gender, culture or age-we are here to serve you.
Our members needs are our passion. We work hard so
that we
can ensure that everyone has the tools necessary to meet her or his personal & professional
goals.
Any article that is cited in another manuscript or other work is required to use the correct reference style. Below is an example of the reference style for SPE articles:
Brown, H. L. and Jones, D. H. 2016, May.
"Insert title of paper here in quotes,"
ANTEC 2016 - Indianapolis, Indiana, USA May 23-25, 2016. [On-line].
Society of Plastics Engineers
Available: www.4spe.org.
Note: if there are more than three authors you may use the first author's name and et al. EG Brown, H. L. et al.
.jpg)
.jpg)
.jpg)
.jpg)
