The SPE Library contains thousands of papers, presentations, journal briefs and recorded webinars from the best minds in the Plastics Industry. Spanning almost two decades, this collection of published research and development work in polymer science and plastics technology is a wealth of knowledge and information for anyone involved in plastics.
The SPE Library is just one of the great benefits of being an SPE member! Are you taking advantage of all of your SPE Benefits?
Karun Kalia, Benjamin Francoeur, Alireza Amirkhizi, Amir Ameli, June 2022
The purpose of this study was to investigate the feasibility of in-situ foaming in fused filament fabrication (FFF) process. Development of unexpanded filaments loaded with thermally expandable microspheres, TEM is reported as a feedstock for in-situ foam printing. Four different material compositions, i.e., two grades of polylactic acid, PLA, and two plasticizers (polyethylene glycol, PEG, and triethyl citrate, TEC) were examined. PLA, TEM and plasticizer were dry blended and fed into the extruder. The filaments were then extruded at the lowest possible barrel temperatures, collected by a filament winder, and used for FFF printing process. The results showed that PLA Ingeo 4043D (MFR=6 g/10min) provides a more favorable temperature window for the suppression of TEM expansion during extrusion process, compared to PLA Ingeo 3052D (MFR=14 g/10min). TEC plasticizer was also found to effectively lower the process temperatures without adversely interacting with the TEM particles. Consequently, unexpanded filaments of PLA4043D/TEM5%/TEC2% was successfully fabricated with a density value of 1.16 g/cm3, which is only ~4.5% lower than the theoretical density value. The in-situ foaming in FFF process was then successfully demonstrated. The printed foams revealed a uniform cellular structure, reproducible dimensions, as well as less print marks on the surface, compared to the solid counterparts.
For several decades, the Tait model has been used in simulation software to describe the volumetric mechanical behavior of thermoplastic polymers as they cool. It is used to compute the residual strains and stresses of the polymer as it solidifies, but there is a problem. Many data sets have coefficients where there exists a discontinuity at the transition between the molten and solid domains. This paper outlines some basic checks that can be done to detect this problem and a procedure to fit the coefficients to data so that this problem does not arise.
Aliya J. Kaplan, Bradley P. Sutliff, Michael J. Bortner, June 2022
Nanofibrillated cellulose (NFC) has properties ideal for applications in the packaging and medical industries. To understand if cellulose-based polymers could become a replacement for synthetic polymers in these fields, NFC suspensions were repeatedly exposed to elevated shear stresses to simulate industrial processing procedures and allow for observation of changes in material properties. A capillary rheometer was used to run aqueous NFC suspensions of 10 wt% at room temperature at shear rates beyond 30,000 s-1. Due to repeated shear rate exposure, a decrease in volume resulting from unavoidable water loss informed the observable increase in apparent viscosity and suggested that this increasing trend was not caused by a change in material morphology. Noisy data as a result of flocs was detrimental to the analysis of material behavior during rheological testing. Once preprocessing procedures are successfully designed to reduce noise in the data, material behavior at high shear rates will be further defined.
Myung-Ho Kim, JaeSik Hyun, InSu Seol , Sunwoong Choi, June 2022
The shear rate-dependent viscosity of natural rubber and three types of synthetic rubber was measured using the Rubber Screw Rheometer. Viscosity values with Mooney viscometer, which has traditionally measured rubber viscosity, have a high correlation with the values of RSR shear rate 10 [1/s]. Thus the Mooney Viscosity value can be estimated using the RSR shear viscosity measurement. Also, in the case of virgin rubber, the accuracy of the measured value increases when it has a pre-shear history. It was confirmed that the viscosity measurement value was a measurement value having a deviation within +3% when comparing the three times repeated measurements. The measured value was correlated to Mooney Viscosity successfully with a first- order equation.
Ethylene-octane copolymer (EOC) with high octane content (45 wt.%) was cross-linked via electron beam irradiation at different dosages (30, 60, 90, and 120 kGy). Effect of irradiation dosage on thermal and mechanical properties was studied. When compared to low density polyethylene, EOC exhibited higher degree of cross-linking reflected in increased gel content, higher elastic modulus (G’), and lower tan obtained by rheology measurement at 150 °C. Cross-linking caused improvement in high temperature creep and also in elastic properties at room and elevated temperatures. Differential scanning calorimetry revealed that e-beam irradiation has caused a gradual reduction in crystallinity and a presence of a fraction with higher melting temperature. In the case of EOC, as the extent of cross-linking increased, stress at break showed an increasing trend whereas irradiation dosage had an inverse effect on elongation at break which could be aroused from the formation of crosslink networks. Radiation dosage has positive effect on thermal stability estimated by thermogravimetric analysis. After 30 min of thermal degradation at 220 °C, slightly higher C=O peak for cross-linked sample was found by Fourier transform infrared spectroscopy while for room temperature samples no C=O peak was detected.
Multi-wall carbon nanotubes (MWCNTs), graphene nanoplates (GNPs), and hybrid fillers (MWCNTs/GNPs) filled thermoplastic polyurethane (TPU) nanocomposites are prepared via melt mixing. The effects of filler (contents of 1, 2, and 3 wt%) and temperature are investigated on the rheological behavior of the TPU nanocomposites. The results demonstrate that the TPU/MWCNT nanocomposites exhibit stronger polymer-filler and filler-filler interactions than TPU/GNP and TPU/GNP/MWCNT nanocomposites. It is found that the nanocomposites with 2 and 3 wt% MWCNTs (2CNT and 3CNT) and 3 wt% MWCNTs/GNPs (3Hybrid) exhibit anomalous rheological behavior. As rising the temperature from 180 to 190 ℃, the complex viscosity values slightly increase in the low frequency region (< 0.4 rad/s) for the 2CNT and 3Hybrid samples, and more significantly increases over a wider frequency range (up to about 10 rad/s) for the 3CNT sample. The Fourier transform infrared spectroscopy spectra demonstrate that the anomalous rheological behavior is not caused by hydrogen bonding in the TPU nanocomposites. The results of scanning electron microscopy observation, time sweep tests, and volume electrical conductivity measurements reveal that the anomalous rheological behavior is attributed to physical contact of the MWCNTs under low shear.
Saurabh Pawale | Karun Kalia | Dylan Cronin | Xiao Zhang | Amir Ameli, August 2021
There is an ever increasing need for sustainable and biobased materials. Plant-based feedstock such as cellulose and lignin can potentially become competitive resources as alternatives to fossil-based materials. Lignin as an inexpensive feedstock has been examined toward preparing polymer composites. It however faces some challenges including its detrimental impact on the mechanical and thermal properties of the resultant composites. This work reports the fabrication and characterization of polylactic acid/lignin composites with the incorporation of a new type of lignin, called deep eutectic solvent (DES) extracted lignin. White fir sawdust was used as feedstock to extract DES lignin. For comparison, commercial alkali lignin (CAL) was also used as a benchmark. PLA/lignin composites containing 0-15 wt.% lignin were fabricated using twin screw extrusion process followed by compression molding. Composites characterization were conducted using thermogravimetric analysis (TGA), differential scanning calorimetry (DSC) and tensile testing. The results revealed that the mechanical and thermal behaviors of DES lignin composites significantly outperformed their CAL counterparts. For composites with 15 wt.% DES, the tensile strength, Young’s modulus, and elongation at break dropped by ~33, 7 and 45%, respectively, compared to those of neat PLA. However, the composites with 15 wt.% CAL showed 90, 45 and 86% drop in the strength, modulus, and elongation, respectively. The initial thermal degradation temperature of PLA dropped by ~ 8-27 °C with the incorporation of 5-15 wt.% DES lignin. On the other hand, the introduction of CAL to PLA lowered the degradation temperature by ~89-124 °C. DSC also showed a drop in the glass transition temperature (Tg) and melt temperature (Tm) for both the composites but the drop was less significant for DES lignin composites. The good performance of PLA/DES lignin composites may be associated with the DES lignin’s high purity, low heterogeneity, low molecular weight, fine particle size as well as its homogenous dispersion and compatibility with PLA matrix.
This study presents the recent development of three-dimensional prediction of cross-linked ethylene propylene diene monomer rubber (EPDM) with chemical blowing agent azodicarbonamide (ADCA) in transfer molding process. Plunger retraction is applied after transfer process is completed. The reaction kinetics model, density model, and viscosity model are applied to describe the complex foamed rubber system in the simulation study. The experimental investigation of material properties into EPDM/ADCA system are studied to make physical parameters in simulation model more realistic. The flow front behavior, the density of foamed rubber, the reaction behavior in foaming and curing conversion are examined to understand the dynamic behavior of the rubber material in both transfer and foaming stages. Furthermore, we study the effect of foaming and plunger retraction. Simulation results show that foaming effect make clamp force larger, however, plunger retraction effect make the back flow occur from cavity to pot to avoid high pressure in the cavity and therefore eliminate the mold clamp force. This study is of great relevance to light weighting application and should reduce the product-to-market cycle time by eliminating the need for the traditional trial-error method.
As designers and engineers continue to push the boundaries of high performance and lightweight design, the use of complex geometries and composite materials is growing. However, traditional composite manufacturing often requires the use of additional tooling and molds which can significantly increase the cost. In this study, a carbon fiber reinforced composite bike saddle is designed and manufactured to demonstrate a newly developed hybrid composite manufacturing process. Using a 3D printed epoxy to print the final part geometry and co-cure pre-impregnated carbon fiber reinforcement, the bike saddle can be optimized, designed and manufactured in less than 24 hours.
Thermoplastics have been blended with reactor-based and grafted-ethylene copolymers for over 50 years to improve room temperature and low temperature ductilityfor many applications, including those in the automotive, appliance, sporting goods industries. The compatibilityof the modifier with the thermoplastic matrix and the rheology of the blend components are key factors in controlling blend morphology. The amount of modifier used and the morphology obtainedaffect the balance of critical properties, including stiffness,impact toughness, and flow. Compatibility of the modifiers with the thermoplastic matrix can be controlled by composition of the modifier produced in-reactor, use of additional compatibilizers (such as diblock copolymers), and by in-situcompatibilization achieved through reactive blending. This paper reviews commercially practiced technologies for impact modification of various thermoplastics based on ethylene copolymers.
In plastic part production, 3D metal printing is a leading manufacturing method for fast, waste-less, and high-accuracy way for making molds with conformal cooling channels. In this automotive power supply test-seat assembly case, the development process combines injection molding simulation, 3D metal printing technology and real experiments to demonstrate an effective mold development approach. Simulation-driven conformal cooling design minimizes the mold temperature difference and significantly reduces part deformation from the traditional straight-line cooling design. Through 6 sets of distance detection, the product dimensions are optimized and can improve the fitting of the three assemblies.
The objective of this study is to use a simulation tool of resin transfer molding (RTM) process to get a comprehensive understanding of the permeabiliy measuring process. In order to varify the simulation tool’s capibility to simulate oil flow in non-matching fabric we build the mesh model of the measuring instrument cavity with the non-matching meshes in this study.
This varifaciton case focuses on two properties of the RTM process, the arriving time and local pressure increasing trend in filling process. By using the simulation tools, we can observe the resin flow within the mold. The comparison between simulation and experiment result shows the reliability of simulation result. We expect that this study will help to clarify relevant issues and then reduce the trial-and-error time and materials.
A complex piece of sporting equipment was molded to customer satisfaction, meeting critical dimensions despite complicated tooling and the use of a crystalline resin. Combining modern simulation techniques and industry expertise proved to be a winning strategy in solving this challenge. The use of post-molding, warp controlling fixtures was completely eliminated from the legacy production process, leading to improved part performance and plant efficiency.
This study compared the longevity performance of polypropylene (PP) and polyethylene (PE) based thermoplastic polyolefin (TPO) waterproofing membranes. It was demonstrated that PE-TPO outperformed PP-TPO for both heat aging and standard UV aging in terms of tensile property retention, weight retention and resistance of surface cracking. Better longevity for PE-TPO is attributed to the lack of tertiary carbon which is intrinsic to PP and prone to chain scission.
Fuel economy and emission regulations are challenging automotive manufacturers to meet global targets, which are becoming more stringent over time, in particular, for internal combustion engine powered vehicles. Internal combustion engines will likely remain dominant for a long time and will require system innovations or in many cases electrification solutions to meet the regulations. This document describes the thermoplastic material solutions to meet the application functional requirements of engine solutions, such as turbocharging, exhaust gas recirculation and gasoline direct injection that are the current trend for system innovations of light-duty vehicles.
The effect of ageing on the adhesion between thermoplastic elastomer materials and glass fiber reinforced polyamide-12 materials was evaluated. Test specimens were made by two-component injection molding, and the melt temperatures and the glass fiber fraction were varied. Adhesion before and after ageing was assessed via peel tests. Ageing (11 weeks at 70 °C with 62% relative humidity) severely reduced the adhesion strength. This could be explained by broken covalent bonds and/or disentanglement in the interphase. The individual materials were not severely affected by the ageing.
Vibration assisted injection molding (VAIM) is a process in which a controlled oscillatory movement is introduced to the injection screw during injection molding. This research was focused on the effect of processing parameters on crystallinity and the crystal structures of poly-lactic acid (PLA) during VAIM. It was observed that vibration assisted injection molded PLA products have higher crystallinity than conventionally molded PLA products under similar conditions. Additionally, the cycle time for fabricating PLA parts can be reduced utilizing VAIM without significant loss of crystallinity. The growth of α´ phase of PLA during VAIM and conventional injection molding process was investigated utilizing an X-Ray diffraction technique. A slight phase change from α´ to α phase can be observed in VAIM samples fabricated under certain conditions. The mean size of crystal structures decreased as VAIM frequency increased to 30Hz.
Continuous fiber reinforced plastics offer excellent weight-specific properties, but their broad introduction to lightweight construction applications is still limited, among other things, due to insufficient accuracy of their processing simulations. A major reason for this is the limited availability of reliable material data and models. In this study, picture frame tests coupled with microscopic analysis are employed to separate the contributions of static weave deformation, lubricated rotational roving friction and roving compression and associated matrix relocation to the total intra-laminar shear forces. This approach allows for additional material insight and helps in developing suitable material models in an efficient way.
In the plastics processing industry, the improvement of the economic efficiency of extrusion lines is important. This is achieved, especially in single-screw extrusion, by an increased throughput at a constant machine size. In order to guarantee high melt quality, new screw concepts are being developed in addition to conventional screws. These include wave-dispersion screws, which are designed to break up the solid bed at an early stage so that the melting and homogeneity behavior is optimized. This paper deals with the experimental comparison of two wave-dispersion screws with a common barrier and 3-section screw. The maximum achievable throughput and in particular the melt quality with regard to thermal and material homogeneity are investigated in order to detect possible advantages of the screw concepts. Here it has been shown that both better thermal and material homogeneity with simultaneously higher possible throughputs can be achieved by wave-dispersion screws.
Currently, only specially treated and compacted carbon fiber recycles can be fed into the twin screw extruder. In this paper, different delivery forms of fibers are characterized in terms of the product quality. The differences between the fibers for twin screw extrusion is illustrated.
84 countries and 60k+ stakeholders strong, SPE
unites
plastics professionals worldwide – helping them succeed and strengthening their skills
through
networking, events, training, and knowledge sharing.
No matter where you work in the plastics industry
value
chain-whether you're a scientist, engineer, technical personnel or a senior executive-nor
what your
background is, education, gender, culture or age-we are here to serve you.
Our members needs are our passion. We work hard so
that we
can ensure that everyone has the tools necessary to meet her or his personal & professional
goals.
Any article that is cited in another manuscript or other work is required to use the correct reference style. Below is an example of the reference style for SPE articles:
Brown, H. L. and Jones, D. H. 2016, May.
"Insert title of paper here in quotes,"
ANTEC 2016 - Indianapolis, Indiana, USA May 23-25, 2016. [On-line].
Society of Plastics Engineers
Available: www.4spe.org.
Note: if there are more than three authors you may use the first author's name and et al. EG Brown, H. L. et al.
.jpg)
.jpg)
.jpg)
.jpg)
