The SPE Library contains thousands of papers, presentations, journal briefs and recorded webinars from the best minds in the Plastics Industry. Spanning almost two decades, this collection of published research and development work in polymer science and plastics technology is a wealth of knowledge and information for anyone involved in plastics.
The SPE Library is just one of the great benefits of being an SPE member! Are you taking advantage of all of your SPE Benefits?
Tensile and tensile-impact test results are reported on specimens with a cold weld line and identical specimens without weld line. Pairs of specimens without and with weld line have been injection molded simultaneously. Test results indicate that the effect of flow-induced stresses on weld line strength should be taken into account, in addition to the well-known influence of material temperatures during molding.
In this paper, we present a unified approach for numerical simulation of thermoforming process. In contrast with iterative methods and dynamic explicit scheme, we propose a high order explicit algorithm based on the classical 4th order Runge-Kutta scheme. The proposed procedure is used to solve the global equilibrium equations and to integrate the sheet viscoelastic constitutive model. The error and time step size control is performed at each level which increase the procedure robustness and efficiency.
The purpose of this investigation is to study the feasibility of PS/PP blends. The analysis of the results shows that compatibilization of the blend with one kind of SBS copolymer improves some mechanical properties of the blend. However, the amount of copolymer to be added depends on the intended specific uses. The cost/profit relation must always be observed.
K.R. Slusarz, C.A. Ronaghan, J.P. Christiano, May 1999
New families of polyolefin resins using single site catalysis technology, are being produced to enhance resin properties. The changes to the molecular architecture of these resins effect the rheological, thermal, frictional, and elastic properties; all of which play a significant role in screw design. This paper will investigate several polyolefin plastomers and compare them to a conventional linear low density polyethylene (LLDPE) to determine their impact on screw design.
On-machine rheology is a methodology of determining the flow characteristics of a material at a given temperature with a specific mold and machine. [5] This methodology can be used to help determine the best injection fill speed to be used for a given material, machine and mold combination. This study presents a mathematical method to obtain an injection fill speed starting point when setting up a new mold, machine and material combination.
I. Pesneau, A. Aït Kadi, M. Bousmina, P. Cassagnau, A. Michel, May 1999
In situ polymer-polymer composites of polypropylene / polyamide (PP/PA) have been obtained by a two step process. In the first step the components were extruded and the blend has been stretched at the exit of the die. In the second step, the blend was molded either by compression or by injection to obtain real organic composite materials with enhanced mechanical and thermal properties.
M. Kontopoulou, E. Takács, J. Vlachopoulos, May 1999
Polymer melt densification, involving particle coalescence followed by the formation and dissolution of bubbles, has been studied in order to evaluate how it is affected by powder properties, chemical structure, thermal properties and rheology. A variety of rotomolding grade resins have been tested, in an effort to understand the mechanisms involved in the melt formation and its subsequent densification.
Adding colorants and additives in masterbatches may affect the rheological properties of the resins into which they are mixed, but the extent of this effect has not been fully investigated. This paper reports on a design of experiments (DOE) study of the effect of 3 common colorants, 2 lubricants, a filler, an antioxidant, and 2 processing parameters (melt temperature and screw speed), on the viscosity of a linear low-density polyethylene (LLDPE) masterbatch. The series of experiments determined that only the lubricant and filler had a significant impact on resin rheology.
An experimental study was undertaken to examine the feasibility of press forming mineral filled and short glass fiber reinforced nylon-6. Press forming was conducted in a matched metal die much like the stamping operation used for sheet metals. The process parameters studied were the sheet preheating temperature, die temperature, forming pressure and sheet clamping. It was shown that with proper adjustment of some of these parameters, both mineral filled and short glass fiber reinforced nylon-6 could be successfully press formed.
Erik Andreassen, Kjetil L. Børve, Kari Rommetveit, Keith Redford, May 1999
Various polypropylene grades were foamed using a small general-purpose twin-screw extruder. Cell diameters of ~70 µm and foam densities of ~14 kg/m3 were achieved with a conventional linear PP, using iso-butane as foaming agent. Linear and branched PP grades were subjected to dynamic rheometry and instrumented haul-off measurements, and the results are discussed in terms of melt strength, viscosity and elasticity. Promising results were obtained for branched materials produced by reactive extrusion.
This paper summarizes a strategy for the numerical simulation of film casting. The strategy incorporates time-stepping, an updated Lagrangian description of motion and viscoelasticity. The results for an approximately viscous solution agree very well with the theoretical solutions. For a Maxwell fluid it is noted that, as the relaxation time increases, the thickness gradient at the die increases and the velocity decreases. Also, for the case considered, a moderate relaxation time seems to destabilize the polymer.
Six years ago we initiated a long term study on the effect of time and temperature on the data sheet modulus values for glass fiber reinforced vinyl composites. Results after the first year showed that the measured creep modulii were higher than those predicted by time-temperature superposition of dynamic mechanical data. This paper presents five years of additional creep data and examines the effect of sample aging on the creep predictions.
It is often difficult to provide consistent surface resistivity in the effective static dissipative range (about 105 to 1010 ohms/square). Thermoplastics incorporating traditional conductive additives generally exhibit discontinuous electrical behavior in this range. Conducting polymer composites have been created through in-situ deposition of conducting polymers onto carbon black substrates. By utilizing the inherent flexibility of these conducting polymer composites, compounds have been developed with controlled surface resistivity.
One of the very first principles used to develop INSITE™ Technology, a major revolution in the polymer industry, was that of learning from history. Analyzing and avoiding repetition of mistakes to do product development worked very much to Dow's advantage as the major piece of technology advanced. Too often not enough time is allotted for contemplation of how to do better based on our collective experiences and wisdom. Particularly in developing new products, experience really makes a huge impact on the speed and success rate.
To meet the challenging processing and performance demands for thin-wall housings, plastic materials must satisfy basic requirements for flow, impact resistance, and modulus. In this paper, select mechanical and processing properties of nylon 6 materials are examined for thin-wall-molding applications and compared with those for amorphous blends.
Automotive body seals are becoming increasingly complex. As there is still little knowledge about the manufacturing process, extensive investigations are done to analyze the influence of the rheological behavior of the materials, the parameters of the extrusion process and the foaming/vulcanization on the quality properties of the foamed seals. The evaluation allows a better process understanding which in combination with improved test methods leads to an increased product quality and reduced manufacturing costs.
Synthetic pearl lustre like other high aspect ratio pigments exhibit poor solid flow behaviour. In the extruder based manufacture of thermoplastic masterbatches this limits output, by restricting the conveying capacity of the feed zone. Proprietary wax encapsulation technology now allows four fold or greater improvements in the extruder output without changing the particle shape or size distribution of the pigment prior to the compounding process. The encapsulation process also leads to low dust characteristics.
R.O. Carter III, John L. Gerlock, Cindy A. Smith, May 1999
The top, clearcoat layer of an automotive paint job protects the under layers while maintaining a beautiful appearance for the life of a car. To determine clearcoat durability, effects of the weathering protocol, of the physical and chemical transformations and effects on the appearance must be considered. To this end, we will describe photoacoustic infrared (PAS-IR), and ultraviolet (UV) technologies and UV microspectroscopy to assay the changes in chemical composition produced in clearcoat paint systems by weathering.
Sindee L. Simon, Olivier Sindt, Gregory B. McKenna, May 1999
The cure kinetics for a commercial epoxy have been established and the influence of the degree of cure on the glass transition determined. Time-temperature and time-conversion superposition principles have been built into a model that successfully predicts the development of the viscoelastic properties of the epoxy during isothermal cure from gelation to vitrification
E. Ray Harrell, Jr., Rabeh H. Elleithy, Coleen A. McFarland, James W. Summers, May 1999
The viscoelastic nature of PVC can not be ignored during the injection molding process. Strains imposed on the compound during the injection stage display recovery dynamics that are indicative of the temperature at which the strains were imposed. A mathematical model, employing approximate" time-temperature modulus relationships provided the basis for interpreting the shrinkage data. A distribution map of the various relative temperatures attained within the part during injection was determined."
84 countries and 60k+ stakeholders strong, SPE
unites
plastics professionals worldwide – helping them succeed and strengthening their skills
through
networking, events, training, and knowledge sharing.
No matter where you work in the plastics industry
value
chain-whether you're a scientist, engineer, technical personnel or a senior executive-nor
what your
background is, education, gender, culture or age-we are here to serve you.
Our members needs are our passion. We work hard so
that we
can ensure that everyone has the tools necessary to meet her or his personal & professional
goals.
Any article that is cited in another manuscript or other work is required to use the correct reference style. Below is an example of the reference style for SPE articles:
Brown, H. L. and Jones, D. H. 2016, May.
"Insert title of paper here in quotes,"
ANTEC 2016 - Indianapolis, Indiana, USA May 23-25, 2016. [On-line].
Society of Plastics Engineers
Available: www.4spe.org.
Note: if there are more than three authors you may use the first author's name and et al. EG Brown, H. L. et al.
.jpg)
.jpg)
.jpg)
.jpg)
